Media Stream Receiver

The Media Stream Receiver provides a method to receive compressed audio streamed over the network.

The maximum number of Media Stream Receivers plus WAN Stream Receivers you can have in a design for each Core is shown in the table below.

Core Model	Max DSP Yes / No	Max Number of Receiver Channels	Max Number of Receivers	Max Number of Muxed A/V Receiver Channels	Max Number of Muxed A/V Receivers
110f	N/A	24	4	24	4
250i	Yes	64	32	96	16
250i	No	64	32	96	32
500i	Yes	64	32	96	16
500i	No	64	32	96	32
510i	Yes	64	32	96	32
510i	No	64	32	96	32
1100	N/A	128	64	96	16
3100	N/A	256	128	192	32
5200	N/A	256	128	192	32

Controls

Control	Function	Default / Range
Peak Level (dBFS)	Meter displaying the Peak audio level.	N / A
Invert	Inverts the audio signal.	Off / On
Mute	Mutes the audio signal.	Off / On
Gain (dB)	Controls the gain.	Default = 0 Range = -100 to 20
Status	This field displays the status of the Receiver in both text and color. The following is a list of possible status colors, and some example conditions. OK - Green - Receiving stream, and audio is good. Compromised - Orange - Receiving stream, but dropouts are detected. Fault - Red –An internal fault occurred - see log for details. Initializing - Blue - Receiver is connecting to stream or waiting for stream to begin. Not Present - Gray - No stream specified.	N / A
URL	Enter the location of the stream source. This can be a source on the internet, or server, etc. Stream Source examples: Unicast RTP streams: rtp://:<port number> (port number specified by the stream source) Example: rtp://:4848 SHOUTcast http://streams1.kpfa.org:8000/kpfa_24 StadiumVision udp://224.8.21.1:2000 SDP http/live555://<IP address>/pcm.sdp SVSi: svsi://<stream number> Example: svsi://2 WyreStorm streams: wyre://<mac_address_of_encoder> Example: wyre://xx:xx:xx:xx:xx:xx (lower-case letters only; colons required) Atlona streams: atlona://<multicast_address_from_encoder>:<port>	N / A
Buffer	Size of the internal network buffer. Longer buffer times improve network dropout resiliency at the expense of increased delay. You can use this control to adjust audio/video sync in mixed systems.	Default = 50.0 Range = 50 ms to 2.0 sec
Interface	The network interface used to receive stream. Unicast sources can generally use “Auto” and the system will select an appropriate interface based on the available routing. All interfaces have Multicast reception enabled, so it may be necessary to specify on which interface multicast streams are present. Interfaces can be LAN A, LAN B, AUX A, AUX B, and can be local or via the internet.	Default = Auto Range = Available network interfaces
Preferred Language ¹	Select the preferred language from the drop-down list. If that language is available in the stream, the Current Language will show the language you selected in the Preferred Language field. The default selection of "- -stream default- -" means whatever language is available is the one used.	Default = "- -stream default- -"
Preferred ISO 639 Language Code ¹	This parameter is available only on the Control Pins of the component. Three-character code reflecting the selection made in the Preferred Language field.	Default = "- -stream default- -"
Current Language ¹	Drop-down list of the languages currently available. The default choice is “- - preferred language - -“, which means, use what you selected in Preferred Language. This control lets you choose what you’re currently listening to and also reflects what’s actually playing. For example, if Preferred Language is set to “- -stream default- -” and Current Language is set to “- -preferred language- -”, once the track starts this control will change to reflect the language you’re actually listening to. You can then use the control to temporarily switch to another track/language. This control is not “sticky” - if the track changes it reverts back to “- -preferred language- -”. Track changes can occur if you change the source control, but can also happen if the remote source changes what is being transmitted.	Default "--preferred language--"
Current ISO 639 Language Code ¹	This parameter is available only on the Control Pins of the component. Three-character code reflecting the selection made in the Current Language field.	Default "--preferred language--"
1. Dependent on what the stream advertises, and is only applicable (currently) to IPTV MPEG TS streams.

Properties

Property	Function	Choices
Name	The name must follow standard naming conventions. The Administrator restricts the name according to the following: ASCII characters a - z, A-Z (case insensitive) Digits 0 - 9 Hyphen (cannot be at the beginning or end of the name) Underscore (acceptable with a Q-SYS implementation) No other characters, symbols, punctuation, or blank spaces.	User Input
Location	The Location is a means by which you can organize your virtual equipment to correspond to your physical equipment. Click in the Location property field, the " Default Location" is highlighted. Type the name of the new location. Once you have entered the new Location name, it is available on the pull-down for the Location property for all other equipment. When you have given the location a name, the related equipment is now displayed under the new location. Any other equipment you identify as being in that location display under that location.	User Input
Mode	Select the type of output Channels. The Media Stream Receiver automatically performs the appropriate up-mixing or down-mixing if the number of output channels differs from the channels available in the input stream.	Stereo Mono Multi-Channel
Channel Count	Available when Mode is set to “Multi-Channel”. If you have multiple Receivers in your design, the maximum total number of received channels is 166 (Cores 1000, 250i, 500i) or 326 (Cores 3000 and 4000).	3 to 16
Multiplexed A/V	When set to Yes, the number of input streams received is limited to 16 for small Cores, and 32 for large Cores. If a Media Stream Receiver will be receiving streams with Audio and Video multiplexed together (e.g. HDTV via MPEG-TS), Multiplexed A/V should be set to “Yes” (the default). The limits for input streams (or Media Stream Components) of 16 for small Cores, 32 for large Cores applies. If the received streams are audio only, Multiplexed A/V may be set to “No” (the limits do not apply). IMPORTANT: If Multiplexed A/V is set to No, and the streams have Multiplexed A/V, you will encounter audio dropouts if you attempt to receive to many streams at one time. NOTE: If you have a large number of possible input streams, but a fairly small number of outputs/listeners, don’t use one Component per input stream attached to a big router. It is better to have only one Component per output/listener and dynamically change the input streams using a script.	Yes / No

Control Pins

The available Control Pins depend on settings in Properties.

Pin Name	Value	String	Position	Pins Available
Channel n Gain	-100 to 20	n dB	0 1	Input / Output
Channel n Invert	0 1	normal invert	0 1	Input / Output
Channel n Mute	0 1	unmute mute	0 1	Input / Output
Channel n Peak Input Level	-120 to 43	-120 dB to 43 dB	0 1	Output
Current ISO 639 Language	Text			Input / Output
Current Language	Text			Input / Output
Interface	Text Input - valid Interface or "Auto"			Input / Output
Preferred ISO 639 Language	Text			Input / Output
Preferred Language	Text			Input / Output
Status	0 1 2 3 4	OK (green) Compromised (orange) Fault (red) Unknown (red) Initializing (blue)	0 0.250 0.500 0.750 1.00	Output
Stream Buffer (seconds)	0.05 to 2.0	50.0ms to 2.00sec	0.00 to 1.00	Input / Output
URL	Text Input - valid URL			Input / Output

Media Stream Receiver

Sources

Codecs

1. Dependent on what the stream advertises, and is only applicable (currently) to IPTV MPEG TS streams.