DDI-11 (DataPort Line Out Adapter) Component

The DDI-11 component enables you to convert the output of one connector on a DataPort card installed in the Core, or an I/O Frame to two standard analog line out connections for use with a non-DataPort amplifier. The component in Q-SYS Designer represents a physical adapter cable available from QSC along with the installation instructions.

IMPORTANT: Use the installation instructions under Alternate Uses in the DDI-11 Installation Guide.

This topic covers the use and configuration of the component in Q-SYS Designer.

When the DDI-11 is used, there is no control or telemetry available through the two associated DataPort card channels - they behave the same as a Line Out card. You must have the DDI-11 component in your design and wired to a DataPort component, and the DDI-11 adapter connected to the DataPort card for this feature to operate. If either is installed, and the other missing, the output is muted.

Controls

There is one set of the following controls for each channel.

Control	Function	Default / Range
Meter (dBu)	Measures the output level.	N / A
Mute	Mutes the output.	Off / On
Invert	Inverts the output.	Not Inverted/Inverted
Gain (dB)	Sets the gain of the output.	Default = 0 Range = -100 to 20

Control

Function

Default / Range

Meter

(dBu)

Measures the output level.

N / A

Mute

Mutes the output.

Off / On

Invert

Inverts the output.

Not Inverted/Inverted

Gain

(dB)

Sets the gain of the output.

Default = 0

Range = -100 to 20

Properties

Property	Function	Choices
Name	User-defined name used for identification. The default name is DDI-11-1, with the final 1 being a sequential number for each component in the design.	User-defined
Location	The Location is a means by which you can organize your virtual equipment to correspond to your physical equipment. The DDI-11 may be on an I/O Frame in Rack 1 for example. Click in the Location property, the " Default Location" is highlighted. Type the name of the new location. Once you have entered the new Location name, it is available on the pull-down for the Location property. When you have given the location a name, the DDI-11 is now displayed under the new location. Any other equipment you identify as being in that location display under that location.

Property

Function

Choices

Name

User-defined name used for identification. The default name is DDI-11-1, with the final 1 being a sequential number for each component in the design.

User-defined

Location

The Location is a means by which you can organize your virtual equipment to correspond to your physical equipment. The DDI-11 may be on an I/O Frame in Rack 1 for example. Click in the Location property, the " Default Location" is highlighted. Type the name of the new location. Once you have entered the new Location name, it is available on the pull-down for the Location property.

When you have given the location a name, the DDI-11 is now displayed under the new location. Any other equipment you identify as being in that location display under that location.

Control Pins

There is one set of the following control pins for each channel.

Pin Name	Value	String	Position	Pins Available
Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Invert	0 1	normal invert	0 1	Input / Output
Meter	-100 to 20	-100 dB to 20 dB	0.000 1.000	Output
Mute	0 1	unmute mute	0 1	Input / Output

Pin Name

Value

String

Position

Pins Available

Gain

-100 to 20

-100 dB to 20 dB

0.000 to 1.00

Input / Output

Invert

normal

invert

Input / Output

Meter

-100 to 20

-100 dB to 20 dB

0.000

1.000

Output

Mute

unmute

mute

Input / Output

QSC.com | Software and Firmware | Resources | QSC Self Help Portal

© 2009 - 2018 QSC, LLC. All rights reserved. QSC and the QSC logo are trademarks of QSC, LLC in the U.S. Patent and Trademark office and other countries. All other trademarks are the property of their respective owners.

http://patents.qsc.com