Flex Out (Core 110f, 110c)

The Flex Channel feature on the Core 110f and Cinema Core 110c provides eight audio channels that can be individually switched between line inputs and line outputs. The Flex Output Component provides the control and selection of the line-level outputs on the Core 110f and Cinema Core 110c. The Flex Output component converts the processed digital signal to analog and provides software controls before and after the convertor. Connections are made using three-terminal 3.5mm Euro style connectors.

Note: The Flex Input and Output components are not for use with QSC DataPort amplifiers.

Controls

Each control listed in the Analog and Digital sections, are one per channel.

Flex I/O

Control	Function	Default / Range
Output	Changes the associated channel to a Flex Output channel. To switch back to a Flex Input channel, you must enable the channel in the Flex Input component.	Default = disabled Range = disabled / enabled

Control

Function

Default / Range

Output

Changes the associated channel to a Flex Output channel.

To switch back to a Flex Input channel, you must enable the channel in the Flex Input component.

Default = disabled

Range = disabled / enabled

Analog

Control	Function	Default / Range
Peak Output Level (dBu)	Measures Peak Output level to the output device.	N / A
Output Mute	Mutes the output after the D-A converter and before the output.	Off / On
Max RMS Output Level (dBu)	Controls the analog RMS output level after the D/A converter. This level is typically set slightly lower than the destination's sensitivity or maximum input level in order to avoid clipping the signal of a power amplifier. Varies in direct proportion with Output Gain.	Default = +21 Range = -40 to +21
Output Gain (dB)	The amount of gain applied to the outgoing analog signal. Varies in direct proportion with the Max RMS Output Level.	Default = 0 Range = -61 to 0

Control

Function

Default / Range

Peak Output Level (dBu)

Measures Peak Output level to the output device.

N / A

Output Mute

Mutes the output after the D-A converter and before the output.

Off / On

Max RMS Output Level (dBu)

Controls the analog RMS output level after the D/A converter. This level is typically set slightly lower than the destination's sensitivity or maximum input level in order to avoid clipping the signal of a power amplifier. Varies in direct proportion with Output Gain.

Default = +21

Range = -40 to +21

Output Gain (dB)

The amount of gain applied to the outgoing analog signal. Varies in direct proportion with the Max RMS Output Level.

Default = 0

Range = -61 to 0

Digital

Control	Function	Default / Range
Peak Output Level (dBFS)	Measures the Digital Signal level prior to the D/A converter.	N / A
Clip	Red LED indicating if the signal is being clipped.	Off / On
Clip Hold	Holds the clip indication until manually cleared.	Off / On
Invert	Inverts the audio signal.	Off / On
Mute	Mutes the digital audio signal.	Off / On
Gain (dB)	Controls the gain of the digital audio signal prior to the D/A converter.	Default = 0 Range = -100 to +20

Control

Function

Default / Range

Peak Output Level (dBFS)

Measures the Digital Signal level prior to the D/A converter.

N / A

Clip

Red LED indicating if the signal is being clipped.

Off / On

Clip Hold

Holds the clip indication until manually cleared.

Off / On

Invert

Inverts the audio signal.

Off / On

Mute

Mutes the digital audio signal.

Off / On

Gain

(dB)

Controls the gain of the digital audio signal prior to the D/A converter.

Default = 0

Range = -100 to +20

Status

Control	Function	Default / Range
Status	Displays the current status of the amplifier both in text and color. The following is a list of possible status colors, and some example conditions. Note: These conditions are examples, and may not be applicable to all components with a Status field. OK – Green – (0) – Audio is good, hardware is good. Compromised – Orange – (1) – Audio is good but a redundancy mechanism is active (one LAN down but the other is still up) or a non-fatal hardware problem exists (fans too slow, temperature higher than expected, etc.) Fault – Red – (2) – Audio is not passing, or hardware is malfunctioning or mis-configured (amplifier power off, audio streams broken, wrong type of I/O Card installed, loudspeaker short circuit, etc.) Missing – Red – (3) – A piece of hardware, defined in the design, has not been discovered. Audio is not passing through that piece of hardware. Initializing – Blue – (5) – In the process of firmware, configuration update, and design start. Audio is obviously bad. Not Present – Gray – A virtual component in the design, that is designated as Dynamically Paired, and Not Required ,has no hardware assigned to it.	N / A

Control

Function

Default / Range

Status

Displays the current status of the amplifier both in text and color. The following is a list of possible status colors, and some example conditions.

Note: These conditions are examples, and may not be applicable to all components with a Status field.

OK – Green – (0) – Audio is good, hardware is good.

Compromised – Orange – (1) – Audio is good but a redundancy mechanism is active (one LAN down but the other is still up) or a non-fatal hardware problem exists (fans too slow, temperature higher than expected, etc.)

Fault – Red – (2) – Audio is not passing, or hardware is malfunctioning or mis-configured (amplifier power off, audio streams broken, wrong type of I/O Card installed, loudspeaker short circuit, etc.)

Missing – Red – (3) – A piece of hardware, defined in the design, has not been discovered. Audio is not passing through that piece of hardware.

Initializing – Blue – (5) – In the process of firmware, configuration update, and design start. Audio is obviously bad.

Not Present – Gray – A virtual component in the design, that is designated as Dynamically Paired, and Not Required ,has no hardware assigned to it.

N / A

Control Pins

Pin Name	Value	String	Position	Pins Available
Analog Level (Peak Output Level (dBu)) meter	-120 to 20	-120 dB to 20 dB	0.000 to 1.00	Output
Clip	0 1	false true	0 1	Output
Clip Hold	0 1	false true	0 1	Input / Output
Digital Level (Peak Output Level (dBFS)) meter	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Output
Flex Output Enable	0 1	false true	0 1	Input / Output
Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Invert	0 1	normal invert	0 1	Input / Output
Max Level (dBu)	-40 to 20	-40.0 to 20	0 to .988	Input / Output
Mute	0 1	unmute mute	0 1	Input / Output
Output Gain	-31 to 0	-31 dB to 0 dB	0.000 to 1.00	Input / Output
Output Mute	0 1	unmute mute	0 1	Input / Output
Status	0 1 2 3 4	OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue)	0 0.250 0.500 0.750 1.00	Output

Pin Name

Value

String

Position

Pins Available

Analog Level
(Peak Output Level (dBu)) meter

-120 to 20

-120 dB to 20 dB

0.000 to 1.00

Output

Clip

false

true

Output

Clip Hold

false

true

Input / Output

Digital Level
(Peak Output Level (dBFS)) meter

-100 to 20

-100 dB to 20 dB

0.000 to 1.00

Output

Flex Output Enable

false

true

Input / Output

Gain

-100 to 20

-100 dB to 20 dB

0.000 to 1.00

Input / Output

Invert

normal

invert

Input / Output

Max Level (dBu)

-40 to 20

-40.0 to 20

0 to .988

Input / Output

Mute

unmute

mute

Input / Output

Output Gain

-31 to 0

-31 dB to 0 dB

0.000 to 1.00

Input / Output

Output Mute

unmute

mute

Input / Output

Status

OK (green)

Compromised (orange)

Fault (red)

Unknown (red)

Updating (blue)

0.250

0.500

0.750

1.00

Output

Software and Firmware | Resources | QSC Self Help Portal | Q-SYS Help Feedback

Flex Out (Core 110f, 110c)

Controls

Flex I/O

Analog

Digital

Status

Properties

Control Pins