Dante Out

The Q-SYS Dante input / output card provides a means of receiving and transmitting to and from other Dante enabled devices on a Dante network.

Properties

Property	Function	Choices
Input/Output Count	Determines the number of input and output channels.	2x2 4x4 8x8 16x16 32x32 64x64
Dante Sample Rate (kHz)	Sets the Sample rate. Available choices are dependent on the selected Input/Output Count.	44.1 48 88.2 96
Dante Receive Latency (milliseconds)	This setting defines the latency between the timestamps on the incoming audio samples and when those samples are played out.	0.15 0.25 0.5 1 5
External Configuration	Determines whether Dante card configuration is allowed by an external program, such as Dante Controller: When set to Yes, you configure the Dante card with an external program. In this mode, some controls within the Dante component in Q-SYS Designer become read-only. When set to No, you configure the Dante card with the Dante component in Q-SYS Designer. In this mode, any changes you make in an external program are ignored.	Yes / No

Controls

Each control listed in the Dante and Digital sections, are one per channel.

Dante

Control	Function	Default / Range
Peak Output Level (dBFS)	Measures Peak Output level to the output device	N / A

Digital

Control	Function	Default / Range
Clip	Red LED indicating if the signal is being clipped.	Off / On
Clip Hold	Holds the clip indication until manually cleared.	Off / On
Invert	Inverts the audio signal.	Off / On
Mute	Mutes the digital audio signal.	Off / On
Gain	Controls the gain of the digital audio signal prior to the D/A converter.	Default = 21 Range = -10 to +21

Status

Control	Function	Default / Range
Status	Displays the current status of the amplifier both in text and color. The following is a list of possible status colors, and some example conditions. Note: These conditions are examples, and may not be applicable to all components with a Status field. OK – Green – (0) – Audio is good, hardware is good. Compromised – Orange – (1) – Audio is good but a redundancy mechanism is active (one LAN down but the other is still up) or a non-fatal hardware problem exists (fans too slow, temperature higher than expected, etc.) Fault – Red – (2) – Audio is not passing, or hardware is malfunctioning or mis-configured (amplifier power off, audio streams broken, wrong type of I/O Card installed, loudspeaker short circuit, etc.) Missing – Red – (3) – A piece of hardware, defined in the design, has not been discovered. Audio is not passing through that piece of hardware. Initializing – Blue – (5) – In the process of firmware, configuration update, and design start. Audio is obviously bad. Not Present – Gray – A virtual component in the design, that is designated as Dynamically Paired, and Not Required ,has no hardware assigned to it.	N / A

Control

Function

Default / Range

Status

Displays the current status of the amplifier both in text and color. The following is a list of possible status colors, and some example conditions.

Note: These conditions are examples, and may not be applicable to all components with a Status field.

OK – Green – (0) – Audio is good, hardware is good.

Compromised – Orange – (1) – Audio is good but a redundancy mechanism is active (one LAN down but the other is still up) or a non-fatal hardware problem exists (fans too slow, temperature higher than expected, etc.)

Fault – Red – (2) – Audio is not passing, or hardware is malfunctioning or mis-configured (amplifier power off, audio streams broken, wrong type of I/O Card installed, loudspeaker short circuit, etc.)

Missing – Red – (3) – A piece of hardware, defined in the design, has not been discovered. Audio is not passing through that piece of hardware.

Initializing – Blue – (5) – In the process of firmware, configuration update, and design start. Audio is obviously bad.

Not Present – Gray – A virtual component in the design, that is designated as Dynamically Paired, and Not Required ,has no hardware assigned to it.

N / A

Config

Control	Function	Default / Range
Label	The name of the output channel on a device. The label must be less than or equal to 31 characters and cannot contain '.' , '=', or '@' characters.	N/A
Flow	The name of the flow. Usage depends on the setting for Properties > External Configuration. External Configuration set to Yes Flow control is read-only, and displays the flow info for the channel as configured in Dante Controller. External Configuration set to No The default is "Auto". The channel will use an automatically configured unicast flow. If you enter a string other than "Auto", the channel is added to the multicast flow with the specified name. A new flow is created if one doesn't already exist with that name. The flow name must be less than or equal to 31 characters and cannot contain '.' , '=', or '@' characters.	N/A
Device Name	The name used to identify the particular device on the network.	N/A

Control Pins

Pin Name	Value	String	Position	Pins Available
Clip	0 1	false true	0 1	Output
Clip Hold	0 1	false true	0 1	Input / Output
Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Invert	0 1	normal invert	0 1	Input / Output
Level	27.0 to -55	27.0 to -55	0 to .988	Output
Mute	0 1	unmute mute	0 1	Input / Output
Tx Flow	(text)			Input / Output
Tx Label	(text)			Input / Output
Device Name	(text)			Input / Output
Output Status	0 1 2 3 4	OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue)	0 0.250 0.500 0.750 1.00	Output