You are here:

Flex In (Core 110f, 110c)

The Flex Channel feature on the Core 110f and Cinema Core 110c provides eight audio channels that can be individually switched between line inputs and line outputs. The Flex Input Component provides the control and selection of the line-level outputs on the Core 110f. The Flex Input component converts the analog signal to digital and provides software controls before and after the convertor. Connections to a single channel are made using a three-terminal 3.5mm Euro style connector.

Note: The Flex Input and Output components are not for use with QSC DataPort amplifiers.

Controls

Input / Output Tab

Flex I/O

Control	Function	Default / Range
Input (Enable)	Changes the associated channel to a Flex Input channel. To switch back to a Flex Output channel, you must enable the channel in the Output Component.	Default = Enabled Range = Enabled / Disabled

Control

Function

Default / Range

Input (Enable)

Changes the associated channel to a Flex Input channel.

To switch back to a Flex Output channel, you must enable the channel in the Output Component.

Default = Enabled

Range = Enabled / Disabled

Mic Detection

Control	Function	Default / Range
Enabled (Yellow LED)	When the LED is on, the associated channel has Mic Detection enabled. When the LED is off, Mic Detection is disabled.	Default = no Range = no / yes
Good (Green LED)	When the LED is green, the mic impedance is within the set thresholds. If the thresholds are exceeded, the green LED is off.	N / A

Control

Function

Default / Range

Enabled

(Yellow LED)

When the LED is on, the associated channel has Mic Detection enabled. When the LED is off, Mic Detection is disabled.

Default = no

Range = no / yes

Good

(Green LED)

When the LED is green, the mic impedance is within the set thresholds. If the thresholds are exceeded, the green LED is off.

N / A

Analog

Control	Function	Default / Range
Peak Input Level (dBFS)	Meters for each channel indicating the peak analog input level. The measurement is taken after the A/D converter, but before the Digital Gain. Use this meter in conjunction with the Max Input Level to obtain an input signal as close to 0 dBFS as possible without actually clipping.	Default = N / A Range = -100 to 20
Clip	Red LED indicating if the signal is being clipped.	Off / On
Clip Hold	Holds the clip indication until manually cleared.	Off / On
Phantom Power	Toggle turning on and off phantom power (+48VDC) to the microphone.	Off / On
Preamp Sensitivity (dBu)	The maximum analog level, coming into the Flex Input component, that can be converted without clipping. This level is typically set slightly higher than the source's output level, so that the Peak Input Level reads about 0 dBFS without actually clipping. Varies inversely with the Preamp Gain.	Default = 21 Range = 21 to -39
Preamp Gain (dB)	The amount of Gain applied to the incoming analog signal level. Varies inversely with the Preamp Sensitivity.	Default = 0 Range = 0 to 60

Digital

Control	Function	Default / Range
Invert	Toggle button to invert the digital output of the Flex Input component.	Off / On
Mute	Mutes the output signal.	Off / On
Gain (dB)	Controls the Gain of the digital output signal.	Default = 0 Range = -100 to 20

Control

Function

Default / Range

Invert

Toggle button to invert the digital output of the Flex Input component.

Off / On

Mute

Mutes the output signal.

Off / On

Gain

(dB)

Controls the Gain of the digital output signal.

Default = 0

Range = -100 to 20

Status

Control	Function	Default / Range
Status	Displays the current text and color status of the component: OK: The device is functioning normally. Initializing: The device is in the process of a firmware or configuration update, or the design is starting. Compromised: The device is functioning, but a non-fatal problem exists. Missing: The device cannot be discovered. Fault: The device is malfunctioning or is not properly configured. Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being pushed to the Core and before it has started running. Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.	N / A

Control

Function

Default / Range

Status

Displays the current text and color status of the component:

OK: The device is functioning normally.
Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
Compromised: The device is functioning, but a non-fatal problem exists.
Missing: The device cannot be discovered.
Fault: The device is malfunctioning or is not properly configured.
Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being pushed to the Core and before it has started running.
Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

N / A

Mic Detection Tab

Detection

Control	Function	Default / Range
Enable (Toggle Button)	Enables or disables Mic Detection for the associated channel. When Mic Detection is on, the impedance of the mic is measured against the set thresholds.	Off / On
Good (Green LED)	When the LED is green, the mic impedance is within the set thresholds. If the thresholds are exceeded, the green LED is off.	Off / On
Impedance	The measured impedance of the attached microphone.	N / A
Set Thresholds (Trigger Button)	Sets the high and low thresholds based on the mic impedance at the time the button is pushed.	N / A

Properties

There are no adjustable properties for the Flex Input component.

Control Pins

Each channel on the Flex Input component has the following Control Pins with the exception of Status.

Pin Name	Value	String	Position	Pins Available
Clip	0 1	false true	0 1	Output
Clip Hold	0 1	false true	0 1	Input / Output
Digital Level	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Output
Flex Input Enable	1 0	enabled disabled	1 0	Input / Output
Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Invert	0 1	normal invert	0 1	Input / Output
Mic Detection Enable (button)	0 1	disabled enabled	0 1	Input / Output
Mic Detection Enabled (LED)	0 1	no yes	0 1	Output
Mic Detection Good	0 1	no yes	0 1	Output
Mic Detection High Impedance Threshold	0 to >100001	--- to >100kΩ	0 to 1.00	Input / Output
Mic Detection Impedance				Output
Mic Detection low Impedance Threshold	0 to >100001	--- to >100kΩ	0 to 1.00	Input / Output
Mic Detection Set Thresholds	Trigger			Input / Output
Mute	0 1	unmute mute	0 1	Input / Output
Phantom Power	0 1	disable enable	0 1	Input / Output
Preamp Gain	0 to 60	0dB to 60dB	0 to 1.00	Input / Output
Preamp Sensitivity	21 to -39	+21dBu to -39dBu	1.00 to 0	Input / Output
Status	0 1 2 3 4	OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue)	0 0.250 0.500 0.750 1.00	Output

Software and Firmware | Resources | QSC Self Help Portal | Q-SYS Help Feedback