Analog In – DCIO/DCIO-H

The Analog Input for the DCIO (and DCIO-H) has two line-level inputs and an input for a microphone. The connectors are physically part of the DCIO. The Analog Input converts the input signal to processed digital and provides software controls before and after the convertor. Connection for the Mike / Line input is provided via a standard three-conductor XLR connector with balanced input, phantom power available in Q-SYS Designer. Used for: mono, non-sync sources including microphone for in-auditorium announcements, and SPL metering. In addition to the XLR, a standard 3.5mm TRS jack, unbalanced, stereo, analog, line-input.

Controls

Analog

Control

Function

Default / Range

Peak Input Level

(dBFS)

Meters for each channel indicating the peak analog input level. The measurement is taken after the A/D converter, but before the Digital Gain. Use this meter in conjunction with the Max Input Level to obtain an input signal as close to 0 dBFS as possible without actually clipping.

Default = N / A

Range ≈100 to 0

Clip

Red LED indicating if the signal is being clipped.

Off / On

Clip Hold

Holds the clip indication until manually cleared.

Off / On

Phantom Power

Toggle turning on and off phantom power (+15VDC) to the microphone. Not available for the Line Inputs.

Off / On

Preamp Sensitivity

(dBu)

The maximum analog level, coming into the Analog Input, that can be converted without clipping. This level is typically set slightly higher than the source's output level, so that the Peak Input Level reads about 0 dBFS without actually clipping.

You can select the field and enter the value you want, or click and drag the number to the value.

Varies inversely with the Preamp Gain.

For Mic Input
Default = 26
Range = 26 to -32

For Line Input
Default = 15
Range = 3 or 15

Preamp Gain knob (Mic Only)

(dB)

The amount of Gain applied to the incoming analog signal level. Varies inversely with the Preamp Sensitivity.

Default = 0

Range = 0 to 58

Preamp Gain buttons (Line Only)

The amount of Gain applied to the incoming analog signal level.

Left and Right toggle buttons toggle the Preamp Gain between 0dB when Off, and 12dB when On. this results in a change in Preamp Sensitivity.

Toggle Button

Preamp Gain

Preamp Sensitivity

Off

0dB

15dBu

On

12dB

3dBu

The values of 0dB and 12dB can be seen by connecting a Custom Controls "Text Display" to the Preamp Gain control pin output.

Default = Off

Range = Off / On

Digital

Control

Function

Default / Range

Invert

Toggle button to invert the digital output of Analog Input.

Off / On

Mute

Toggle button to mute and unmute the output signal.

Off / On

Gain

(dB)

Controls the Gain of the digital output signal.

Default = 0

Range = -100 to 20

Status

Control

Function

Default / Range

Status LED

This LED changes color to indicate the current status of the Core. See Status for the meanings of the various colors.

N / A

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

  • OK: The device is functioning normally.
  • Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
  • Compromised: The device is functioning, but a non-fatal problem exists.
  • Missing: The device cannot be discovered.
  • Fault: The device is malfunctioning or is not properly configured.
  • Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being pushed to the Core and before it has started running.
  • Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

N / A

Properties

There are no adjustable properties for the Analog Input .

Control Pins

The Analog Input has the following Control Pins.

Pin Name

Value

String

Position

Pins Available

Clip

0

1

false

true

0

1

Output

Clip Hold

0

1

false

true

0

1

Input / Output

Level

≈ -100 to 20

≈ -100 dB to 20 dB

0 to 1.00

Output

Gain

-100 to 20

-100 dB to 20 dB

0. to 1.00

Input / Output

Invert

0

1

normal

invert

0

1

Input / Output

Mute

0

1

unmute

mute

0

1

Input / Output

Phantom Power

0

1

disable

enable

0

1

Input / Output

Preamp Gain

Mic Channel

Left / Right Channel

(dB)

 

0 to 58

0 or 12

 

0dB to 58dB

0dB or 12dB

0 to 1.00

0 to 1.00

Input / Output

Input / Output

Preamp Sensitivity

(dBu)

+26 to -32

+26dBu to -32dBu

0 to 1.00

Input / Output

Status

0

1

2

3

4

OK (green)

Compromised (orange)

Fault (red)

Unknown (red)

Updating (blue)

0

0.250

0.500

0.750

1.00

Output