GPIO (Core 250i, 500i, 510i, 1100, 3100, and I/O Frame)

This topic describes how to configure and control the General Purpose Input Output (GPIO) hardware interfaces in Q-SYS Designer.

The General Purpose Input Output (GPIO) interface is used to integrate Q-SYS with custom or third-party controls. The GPIO allows you to control external hardware and certain aspects of Q-SYS using external hardware. In addition, you can use the GPIO to supply an external word clock to Q-SYS for synchronization. Refer to the Core Status topic for details. The GPIO selections require an external TTL level word clock: pin 3 is signal, pin 8 is ground. When you select GPIO A-1 or GPIO B-1 as the clock source, the respective GPIO 1 Property changes to "Input used as clock source". The clock source should be connected to pin 3 of the respective GPIO connector - either GPIO A or GPIO B.

Note: Typically, Internal is used as the clock source. Only if there is a need to synchronize the Q-SYS system to an external clock would you use GPIO or AES3. You would use GPIO if the external clock signal is a word clock. You would use AES3 if the external clock signal is an AES3 signal. Often an AES3 signal without audio is used to reduce the clock jitter. This signal is called AES3 black.

Some examples of hardware to which you can connect are: Potentiometers, buttons, switches, LED/lights, motors (including fans) relays, and temperature and humidity sensors.

The GPIO interface is physical hardware, and is represented in Q-SYS Designer by the GPIO component. There are two GPIO interfaces available in a Core, and one in an I/O Frame. The external connection to the GPIO interface is supplied via a standard DA-15 connector. A GPIO component is configured in Q-SYS Designer (GPIO component Properties) where there are eight configurable pins that represent and configure GPIO-1 through GPIO-8 in the DA-15 connector. You can configure these pins to be Inputs, Outputs, Digital, Analog, Clocks, and so on.

The GPIO is protected by self-resetting fuses.

DB-15 Pin #

Signal Name

Signal Type

Description

1

RNO

Relay Contact

Relay Normally Open 1

2

RNC

Relay Contact

Relay Normally Closed 1

3

GPIO-1

Normal Current

Configurable 2

4

GPIO-3

Normal Current

Configurable

5

Power

Power

+12 VDC

6

GPIO-5

High Current

Configurable

7

GPIO-7

High Current

Configurable

8

GND

Ground

Ground

9

RC

Relay Common

Relay Common 1

10

GND

Ground

Ground

11

GPIO-2

Normal Current

Configurable

12

GPIO-4

Normal Current

Configurable

13

Power

Power

+12 VDC

14

GPIO-6

High Current

Configurable

15

GPIO-8

High Current

Configurable
1. The GPIO Relay is controlled in a Q-SYS Design.
2. When Using a Word Clock. The GPIO input impedance is much higher than what would normally be required to terminate a word clock signal. QSC recommends using a termination resistor between pin 3 and ground (pin 8 or 10). The resistor value should match the cable impedance. If the cable impedance is unknown, use 75 Ohm. Refer to the GPIO component for more information about external clocks.
Name Normal Current Pins High Current Pins

Maximum Input Range

0 V to 32 V

0 V to 32 V

Analog Input Range

0 V to 24 V

0 V to 24 V

Digital Input, Low

0.8 V maximum

0.8 V maximum

Digital Input, High

2.0 V minimum

2.0 V minimum

Digital Output, Low

0.4 V maximum

0.4 V maximum

Digital Output, High

2.4 V minimum, 3.3 V maximum

2.4 V minimum, 3.3 V maximum

Digital Output Impedance

1 k ohm

1 k ohm

High Current Output, Low

N / A

0.4 V maximum

High Current Output, High

N / A

11 V minimum, 13 V maximum

High Current Output sink

280 mA

280 mA

High Current Output source

N / A

280 mA
Specifications

Relay Pins

Maximum Voltage, relative to Ground

30 V

Maximum Current through Relay

1 Amp

Power Pins

Output Voltage

11 V min

13 V max

Maximum Output Current

400 mA

All Power and High Current pins combined

Maximum Source Current

400 mA

All GPIO Pins 1 through 8 combined

Maximum Sink Current

1 A using 1 GND pin

2 A using 2 GND pins

There are four possible "Directions" you can select for the GPIO pins.

Property

Value

Unused

The default position, and anytime the GPIO Pin is not in use

Input

Devices or signals connected to a configurable pin provide an input to the Q-SYS system.

Output

The Q-SYS hardware will be providing signals to devices connected to configurable pins.

Raw

The Raw mode is for advanced capabilities. If there is something you cannot do in the standard choices, contact QSC Support for detailed information.

Property

GPIO Pins

Value

Input used as clock source

3

When the Core Clock Source Property is set to GPIO A-1 or GPIO B-1, this GPIO is used only for the clock source.

The GPIO selections require an external TTL level word clock: pin 3 is signal, pin 8 is ground. When you select GPIO A-1 or GPIO B-1 as the clock source, the respective GPIO 1 Property changes to "Input used as clock source". The clock source should be connected to pin 3 of the respective GPIO connector - either GPIO A or GPIO B.

Note: Typically, Internal is used as the clock source. Only if there is a need to synchronize the Q-SYS system to an external clock would you use GPIO or AES3. You would use GPIO if the external clock signal is a word clock. You would use AES3 if the external clock signal is an AES3 signal. Often an AES3 signal without audio is used to reduce the clock jitter. This signal is called AES3 black.

Digital
(TTL 3.3 VDC @ 2 mA)

1 to 8

Digital zero = 0

Digital one = 3.3

Potentiometer
(10 k Ohm, 12 V)

1 to 8

Allows a potentiometer to be connected to the GPIO pin, the position of which is represented by the control in the GPIO Control Panel. The value or range is 0 to 1.

Analog
(0-24 V. Low Z)

1 to 8

Input 0 to 24 V, Low Z

12-bit Resolution

Contact Closure

1 to 8

Allows a button, switch, or other binary device to be connected to the GPIO Relay contact.

WCP-1 3

1 to 8

Interfaces with QSC's Wall Control Plate, version 1.

WCP-2
(requires 3 pins) 3

1-3 and/or 5-7

Interfaces with QSC's Wall Control Plate, version 2. Requires four configurable pins, selected on GPIO 1 and/or 5 only.  

Optical Rotary Encoder
(requires 2 pins)

1-2, 3-4, 5-6, or 7-8

Allows an Optical Rotary Encoder to be connected to two configurable pins.

Mechanical Rotary Encoder
(requires 2 pins)

1-2, 3-4, 5-6, or 7-8

Allows a Mechanical Rotary Encoder to be connected to two configurable pins.
3. For more information on WCP-1 or WCP-2: WCP Manual

Property

GPIO Pins

Value

Digital Output

1 to 8

Digital zero = 0

Digital one = 1

Pulse Width Modulated (PWM) Output

Good for operating a Fan or a DC motor that will likely require 12 V High Drive, High Current.

1 to 8

Pulse Width is set in the Control Panel 0 - 100%

Pulse Frequency is set in the Control Panel 50 to 50,000 Hz

Inverted Pulse Width Modulated (PWM) Output

If this pin is used in conjunction with the non-inverted PWM, linking the PWM Duty Control Pins together will produce opposite but equal signals since they must use the same frequency.

1 to 8

Pulse Width is set in the Control Panel 0 - 100%

Pulse Frequency is set in the Control Panel 50 to 50,000 Hz

No Clock output available on these pins

1 and 5

N / A

Sample Clock

2 and 6

System Frequency

48 kHz

Vector Clock

3 and 7

3 kHz

6 kHz

Frame Clock

Mainly intended for software debug.

4 and 8

Programmable - 30 Hz to 120 Hz

Property

Value

GPIO Pins 1 - 4

3.3 V TTL

Open Collector High Current

GPIO Pins 5 - 8

3.3 V TTL

12 V Push-Pull High Current

12 V High-Drive High Current

Open Collector High Current

The Raw mode is for advanced capabilities. If there is something you cannot do in the standard choices, contact QSC Support for detailed information. Note that when you select Raw as the direction, there are two instances of that pin on the GPIO component; one input, and one output.

The Controls are displayed in GPIO Pin number order, 1 through 8, from left to right in the Control Panel with the related DA-15 pin number listed. The DA-15 pin / GPIO pin number relationship can change based on the controls assigned to the GPIO pins.

General

Control

Function

Default / Range

Relay

The function of the Relay button is to open and close the contacts of the relay on the GPIO Interface.

RNO 1 (Relay Normally Open on DA-15 Pin 1)

RNC 2 (Relay Normally Closed on DA-15 Pin 2)

RC 9 (Relay Common on DA-15 Pin 9)

Off / On

Digital In

(Indicator)

This LED lights when there is a Digital input of 1 (3.3 V TTL) present.

Off / On

Analog In

(VDC)

This is a read-only knob that displays the DC voltage applied to the GPIO pin.

Default = 0

Range = 0 to 12

Digital Out

This toggle button supplies a 0 in the Off position and a 1 in the On position.

Off / On

PWM Duty (Percentage)

Sets the percentage of a period when the pulse is positive.

Default = 0

Range = 0 to 100

PWM Frequency

(Hz)

Sets the period time. (1 / frequency)

Affects all PWM outputs

Default = 50

Range = 5 to 50,000

The GPIO pins display as control pins on the GPIO component and are always present except when "Unused" is selected for a pin's Direction. The GPIO pins are not used to change controls in the Control Panel. Some of the Direction/Type combinations provide Control Pins you can use to change the Controls within the Control Panel.

The Relay Out Control Pin is always available.

Pin Name

Value

String

Position

Pins Available

Relay Out

0

1.00

false (normal)

true (activated)

0

1.00

Input / Output

The Pin Name reflects the Input Type you select for a given GPIO pin. Indented below each GPIO Type are any Control Pins that may be available for that Type.

Pin Name

Value

String

Position

Pins Available

Digital Input

0

1

false

true

0

1

Output

Contact Closure

0

1

false

true

0

1

Output

Potentiometer (10k Ohm, 12 V) and Potentiometer (2-wire)

0 to 1

N / A

0 to 1.00

Output

Calibrate Maximum

 

 

 

 

Calibrate Minimum

 

 

 

 

Maximum Position

 

 

 

 

Minimum Position

 

 

 

 

Analog Input

0 to 24.00

0.00 V to 24.0 V

0 to 1.00

Output

WCP-1

0.00

1.00

2.00

3.00

4.00

5.00

6.00

7.00

8.00

9.00

10.00

0

1

2

3

4

5

6

7

8

9

10

0

.100

.200

.300

.400

.500

.600

.700

.800

.900

1.00

Output

WCP-2

1.00

2.00

3.00

4.00

5.00

6.00

1

2

3

4

5

6

0

.200

.400

.600

.800

1.00

Output

Rotary Encoder (Mechanical or Optical)

0 to 1.00

N / A

0 to 1.00

Input / Output

Rotary Encoder Resolution

4 to 4096

4 to 4096

0 to 1.00

Input / Output

Rotary Encoder Reverse

0

1.00

normal

invert

0 to 1.00

Input / Output

The Pin Name reflects the Output Type that must be selected for a particular Control Pin to be available.

Pin Name

Value

String

Position

Pins Available

Digital Output 1

0

1

false

true

0

1

Input / Output

PWM Output

0 to 100

—

0 to 1.00

Input / Output

PWM Duty

0 to 100

0% to 100%

0 to 1.00

Input/Output

PWM Invert

0

1.00

normal

inverted

0 to 1.00

Input / Output

PWM Frequency

5 to 50,000

5.00Hz to 50.0kHz

0 to 1.00

Input / Output

Inverted PWM Output

0 to 100

—

0 to 1.00

Input / Output

PWM Duty

0 to 100

0% to 100%

0 to 1.00

Input/Output

PWM Invert

0

1.00

normal

inverted

0 to 1.00

Input / Output
1. When Digital Output is selected, the Control Pin for the "Digital Out" button in the Control Panel displays as an input to the selected GPIO pin. It is not shown in the Control Pins list as other "Control Pins".

Button or Potentiometer

LED - Light - Motor

Directional Motor

Rotary Encoder

Rotary Switch

All resistors should have the same value. The total resistance should be about 10K Ohms. The individual resistor value should be 10,000 divided by the number of resistors. The schematic is an example only, and could easily be modified to have more switch positions or use multiple momentary buttons instead of a rotary switch.

Q-SYS device GPIO output states are undefined during boot-up and design redeploy. In the following tables, "While On" and "While Off" indicate the button position as defined in the running design file. During a reboot or redeploy, the position may toggle depending on the GPIO type before returning to the defined position after the design starts running.

Bold text indicates a temporary GPIO position toggle during boot-up and redeploy.

GPIO Type

While On

While Off

Digital Output

Toggles to Off

Stays Off

Open Collector

Toggles to Off

Stays Off

Raw

Stays On

Toggles to On

GPIO Type

While On

While Off

Digital Output

Stays On

Toggles to On

Open Collector

Toggles to Off

Stays Off

Raw

Stays On

Toggles to On

GPIO Type

While On

While Off

Digital Output

Toggles to Off

Stays Off

Open Collector

Toggles to Off

Stays Off

Raw

Stays On

Toggles to On

GPIO Type

While On

While Off

Digital Output

Toggles to Off

Stays Off

Open Collector

Stays On

Toggles to On

Raw

Stays On

Toggles to On