Flex Out (Core 110f, 110c)

The Flex Channel feature on the Core 110f and Cinema Core 110c provides eight audio channels that can be individually switched between line inputs and line outputs. The Flex Output Component provides the control and selection of the line-level outputs on the Core 110f and Cinema Core 110c. The Flex Output component converts the processed digital signal to analog and provides software controls before and after the convertor. Connections are made using three-terminal 3.5mm Euro style connectors.

Note: The Flex Input and Output components are not for use with QSC DataPort amplifiers.

Controls

Each control listed in the Analog and Digital sections, are one per channel.

Flex I/O

Control	Function	Default / Range
Output	Changes the associated channel to a Flex Output channel. To switch back to a Flex Input channel, you must enable the channel in the Flex Input component.	Default = disabled Range = disabled / enabled

Control

Function

Default / Range

Output

Changes the associated channel to a Flex Output channel.

To switch back to a Flex Input channel, you must enable the channel in the Flex Input component.

Default = disabled

Range = disabled / enabled

Analog

Control	Function	Default / Range
Peak Output Level (dBu)	Measures Peak Output level to the output device.	N / A
Output Mute	Mutes the output after the D-A converter and before the output.	Off / On
Max RMS Output Level (dBu)	Controls the analog RMS output level after the D/A converter. This level is typically set slightly lower than the destination's sensitivity or maximum input level in order to avoid clipping the signal of a power amplifier. Varies in direct proportion with Output Gain.	Default = +21 Range = -40 to +21
Output Gain (dB)	The amount of gain applied to the outgoing analog signal. Varies in direct proportion with the Max RMS Output Level.	Default = 0 Range = -61 to 0

Digital

Control	Function	Default / Range
Peak Output Level (dBFS)	Measures the Digital Signal level prior to the D/A converter.	N / A
Clip	Red LED indicating if the signal is being clipped.	Off / On
Clip Hold	Holds the clip indication until manually cleared.	Off / On
Invert	Inverts the audio signal.	Off / On
Mute	Mutes the digital audio signal.	Off / On
Gain (dB)	Controls the gain of the digital audio signal prior to the D/A converter.	Default = 0 Range = -100 to +20

Status

Control	Function	Default / Range
Status	Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition: OK: The device is functioning normally. Initializing: The device is in the process of a firmware or configuration update, or the design is starting. Compromised: The device is functioning, but a non-fatal problem exists. Missing: The device cannot be discovered. Fault: The device is malfunctioning or is not properly configured. Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being pushed to the Core and before it has started running. Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.	N / A

Control

Function

Default / Range

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

OK: The device is functioning normally.
Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
Compromised: The device is functioning, but a non-fatal problem exists.
Missing: The device cannot be discovered.
Fault: The device is malfunctioning or is not properly configured.
Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being pushed to the Core and before it has started running.
Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

N / A

Properties

There are no adjustable properties for the Flex Output component.

Control Pins

Pin Name	Value	String	Position	Pins Available
Analog Level (Peak Output Level (dBu)) meter	-120 to 20	-120 dB to 20 dB	0.000 to 1.00	Output
Clip	0 1	false true	0 1	Output
Clip Hold	0 1	false true	0 1	Input / Output
Digital Level (Peak Output Level (dBFS)) meter	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Output
Flex Output Enable	0 1	false true	0 1	Input / Output
Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Invert	0 1	normal invert	0 1	Input / Output
Max Level (dBu)	-40 to 20	-40.0 to 20	0 to .988	Input / Output
Mute	0 1	unmute mute	0 1	Input / Output
Output Gain	-31 to 0	-31 dB to 0 dB	0.000 to 1.00	Input / Output
Output Mute	0 1	unmute mute	0 1	Input / Output
Status	0 1 2 3 4	OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue)	0 0.250 0.500 0.750 1.00	Output