Attero Tech unDX2IO+

The extension is compatible with Q-SYS Designer version 8.4 and above and Attero Tech firmware version 4.6.0 and above.

1. In the NIC field, select the interface through which the extension will communicate to control the device.
2. In the IP field, specify the IP address of the device and press Enter.

The extension will automatically attempt a connection. The "Connected" LED glows green once a connection is established. If the extension loses its connection to the device, it will attempt to re-establish the connection every 5 seconds.

Note: If Dante Lock is active on the connected device, you will see a padlock icon next to the device name.

Name

The Name may contain ASCII letters 'a' through 'z' (case-insensitive), the digits '0' through '9', and the hyphen. Names cannot begin or end with a hyphen. No other symbols, punctuation characters, or blank spaces are permitted.

Location

User-defined name that groups the component with other components in the same physical location, or in the same organizational scheme.

Is Required

When set to 'Yes' (default), and the device is not found on the network, the device is reported as 'Missing', which is an error condition. When set to 'No', and the device is not found on the network, the device is reported as 'Not Present', which is not an error condition.

Show Debug

Select 'Yes' to show the Debug Output window. For details, see Debug Output.

Refresh

Although the extension monitors the device settings for changes automatically, this button manually triggers the extension to retrieve the current settings and update the extension values to match.

Meters

Enables metering within the extension. The extension polls for metering information once a second and updates signal presence indicators and Dante Rx status for each channel accordingly. The metering function remains active until manually turned off. Click the button to toggle between states.

Identify

Causes the power LED on the front of the device to start blinking so it can easily be identified. The identify function remains active until manually turned off. Click the button to toggle between states.

Status

Normally, this shows "Initializing" for a few moments after starting your design, followed by "OK". If you see a "Fault" status, check your connection parameters. If you see "Missing", ensure that the device is powered on and connected to the network.

Details

Provides information on the connected device such as MAC address, IP address, MCU version, and parameter lock state.

Save as Default

Forces the device to save its current settings as the new power-on defaults.

Input Settings

Signal Indicator

Shown in top right corner of each channel. Only active when metering is enabled.

• Green = signal
• Grey = no signal (<60dB)
• Red = clipping

Gain

For channels 1 and 2 only, selects the gain level for the input. Options are:

• Line (-15dB pad)
• Line (no pad)
• Low Mic (+25dB)
• High Mic (+40dB)

Phantom

For channels 1 and 2 only, selects the state of phantom power for the input. If the button is grey, the phantom power is inactive. If it’s orange, the phantom power is active. Click the button to toggle between states.

Input Pad

For channels 3 and 4 only, selects the sensitivity for the input. Options are:

• -10dBV (consumer level)
• +4dBu (pro level)

Output Settings

Signal Indicator

Shown in top right corner of each channel. Only active when metering is enabled.

• Green = signal
• Grey = no signal (<60dB)
• Red = clipping

Dante Rx Name

The name of the channel as displayed in Dante Controller.

Volume

Sets the output volume on each output. Click and drag to adjust from a minimum of -60dB to a maximum of 0dB.

Mute

Allows muting of an output. If the button is grey, the mute is inactive. If it’s orange, the mute is active. Click the button to toggle between states.

Dante Rx Indicator

Active only when metering is enabled. Shows the state of the Dante connection. Use Dante Controller to investigate any errors or warnings.

• Green = connected and OK
• Grey = no connection
• Red = connection error
• Yellow = connection warning

Pin Name	Value	String	Position	Pins Available
Dante Rx State
1, 2	0 1	false true	0 1	Output
Device
Connected	0 1	false true	0 1	Output
Dante Lock	0 1	false true	0 1	Output
Identify	0 1	false true	0 1	Input / Output
Metering	0 1	false true	0 1	Input / Output
Status	0 1 2 3 4 5	OK (Green) Compromised (Orange) Fault (Red) Not Present (Gray) Missing (Red) Initializing (Blue)	-	Output
Input Gain
1, 2	-	Line (-15dB pad) Line (no pad) Low Mic (+25dB) High Mic (+40dB)	-	Input / Output
Input Pad
3, 4	0 1	false true	0 1	Input / Output
Input Signal Presence
1, 2, 3, 4	0 1	false true	0 1	Output
Output Mute
1, 2	0 1	false true	0 1	Input / Output
Output Signal Presence
1, 2	0 1	false true	0 1	Output
Output Volume
1, 2	-60 to 0	-60dB to 0dB	0.00 to 1.00	Input / Output
Phantom Power
1, 2	0 1	false true	0 1	Input / Output
Disable1	0 1	disabled enabled	0 1	Input / Output

1. Use this control pin to enable or disable the extension in your design. When Disabled is set to enabled (value of 1), the Connection Status changes to "Not Present - Disabled".

If you've successfully connected to the device but all of the controls are locked and disabled, this means that parameter locking is enabled in the unIFY app. To use the extension, disable the parameter lock in unIFY.