POTS In

The POTS In component receives the incoming audio from a telephone call, converts the analog signal to digital, and monitors and modifies the audio using the controls listed below.

Properties

Telephony (Core 110f, Core 110c, and POTS card only)

Property	Function	Choices
Telephone Country	Select the country in which the telephone service resides.	Multiple Default = USA
Telephone Tone Output	When 'Yes' is selected, the Ring, Entry, Exit, and DTMF tones are fed to a separate output channel (Tone Output) on the POTS In component. These tones can now be routed independent of the voice audio.	No / Yes

Property

Function

Choices

Telephone Country

Select the country in which the telephone service resides.

Multiple

Default = USA

Telephone Tone Output

When 'Yes' is selected, the Ring, Entry, Exit, and DTMF tones are fed to a separate output channel (Tone Output) on the POTS In component. These tones can now be routed independent of the voice audio.

No / Yes

Controls

Line

Control	Function	Default / Range
Peak Input Level (dBFS)	Measures the analog input signal.	Green = good Yellow = close to clipping Red = clipping
Clip	Red LED indicating if the signal is being clipped.	Off / On
Clip Hold	Holds the clip indication until manually cleared by pressing this button to the Off position.	Off / On

Control

Function

Default / Range

Peak Input Level

(dBFS)

Measures the analog input signal.

Green = good

Yellow = close to clipping

Red = clipping

Clip

Red LED indicating if the signal is being clipped.

Off / On

Clip Hold

Holds the clip indication until manually cleared by pressing this button to the Off position.

Off / On

Digital

Control	Function	Default / Range
Invert	Toggle button to invert the digital output of the POTS In.	Off / On
Mute	Mutes the output signal.	Off / On
Gain (dB)	Controls the Gain of the digital output signal.	Default = 0 Range = -100 to 20

Control

Function

Default / Range

Invert

Toggle button to invert the digital output of the POTS In.

Off / On

Mute

Mutes the output signal.

Off / On

Gain

(dB)

Controls the Gain of the digital output signal.

Default = 0

Range = -100 to 20

Status

Control	Function	Default / Range
Status LED	This LED changes color to indicate the current status of the Core. See Status for the meanings of the various colors.	N / A
Status	Displays color-coded messages indicating the current status of the active Core. Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition: OK: The device is functioning normally. Initializing: The device is in the process of a firmware or configuration update, or the design is starting. Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details. Missing: The device cannot be discovered. Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details. Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running. Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.	N / A

Control

Function

Default / Range

Status LED

This LED changes color to indicate the current status of the Core. See Status for the meanings of the various colors.

N / A

Status

Displays color-coded messages indicating the current status of the active Core.

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

OK: The device is functioning normally.
Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
Missing: The device cannot be discovered.
Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

N / A

Control Pins

Pin Name	Value	String	Position	Pins Available
Channel n Clip	0 1	false true	0 1	Output
Channel n Clip Hold	0 1	false true	0 1	Input / Output
Channel n Digital Level	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Output
Channel n Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Channel n Invert	0 1	normal invert	0 1	Input / Output
Channel n Mute	0 1	unmute mute	0 1	Input / Output
Status	Text			Output