POTS Out

The POTS Out component converts the processed digital signal to analog and provides software controls before and after the convertor. The output is sent to the POTS telephone system servicing the call.

Properties

Telephony (Core 110f, Core 110c, and POTS card only)

Property	Function	Choices
Telephone Country	Select the country in which the telephone service resides.	Multiple Default = USA
Telephone Tone Output	When 'Yes' is selected, the Ring, Entry, Exit, and DTMF tones are fed to a separate output channel (Tone Output) on the POTS In component. These tones can now be routed independent of the voice audio.	No / Yes

Property

Function

Choices

Telephone Country

Select the country in which the telephone service resides.

Multiple

Default = USA

Telephone Tone Output

When 'Yes' is selected, the Ring, Entry, Exit, and DTMF tones are fed to a separate output channel (Tone Output) on the POTS In component. These tones can now be routed independent of the voice audio.

No / Yes

Controls

Line

Control	Function	Default / Range
Peak Line Level (dBm @600Ω)	Measures Peak Output level to the RJ11 output.	-120 to 27

Digital

Control	Function	Default / Range
Peak Output Level (dBFS)	Measures the Digital Signal level prior to the D/A converter.	Green = good Yellow = close to clipping Red = clipping
Clip	Red LED indicating if the signal is being clipped.	Off / On
Clip Hold	Holds the clip indication until manually cleared.	Off / On
Invert	Inverts the audio signal.	Off / On
Mute	Mutes the digital audio signal. Note: Note: Dialing is enabled regardless of the Mute state.	Off / On
Gain	Controls the gain of the digital audio signal prior to the D/A converter.	Default = 0 Range = -100 to +20

Status

Control	Function	Default / Range
Status	Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition: OK: The device is functioning normally. Initializing: The device is in the process of a firmware or configuration update, or the design is starting. Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details. Missing: The device cannot be discovered. Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details. Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running. Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.	N / A

Control

Function

Default / Range

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

OK: The device is functioning normally.
Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
Missing: The device cannot be discovered.
Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

N / A

Control Pins

Pin Name	Value	String	Position	Pins Available
Channel n Clip	0 1	false true	0 1	Output
Channel n Clip Hold	0 1	false true	0 1	Input / Output
Channel n Digital Level	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Output
Channel n Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Channel n Invert	0 1	normal invert	0 1	Input / Output
Channel n Mute	0 1	false true	0 1	Input / Output
Channel n Peak Line Level (dBm @ 600Ω)	-120 to 27	-120 dB to 27 dB	0.000 to 1.00	Output