Status (NL Series, NM Series, QIO Series)

The Status component for the NL Series network loudspeakers, NM Series beamforming microphones, and QIO Series network expanders provides health information about these devices, including overall status, network information, detected power, and audio stream health (NL Series only).

Refer to these hardware topics for an overview of NL Series, NM Series, and QIO Series peripherals:

Name

The Name may contain ASCII letters 'a' through 'z' (case-insensitive), the digits '0' through '9', and the hyphen. Names cannot begin or end with a hyphen. No other symbols, punctuation characters, or blank spaces are permitted.

Note: This name must match the Hostname for the device as defined in Core Manager or Peripheral Manager.

Location

User-defined name that groups the component with other components in the same physical location – for example, "Rack 1" – or in the same organizational scheme.

Is Network Redundant

Select whether the device is connected to redundant networks.

Is Required

When enabled, and the device is not found on the network, the device is reported as 'Missing', which is an error condition. This is the default behavior. When disabled, and the device is not found on the network, the device is reported as 'Not Present', which is not an error condition.

Dynamically Paired

Indicates that this virtual component can be paired with the same type of hardware without changing the network ID of the hardware or the name of this component. Refer to the Q-SYS Core Manager Dynamic Pairing topic for more information. The default is 'No'.

RJ45 LED Disable

(NM Series only) Select whether the yellow (activity) and green (link speed) LAN jack status LEDs are illuminated on the underside of the NM-T1. The default is No (not disabled).

PoE+ Enable

(NL Series only) Determines whether the loudspeaker advertises itself on the network as a PoE+ capable device, which affects how the loudspeaker uses the PoE power budget of the connected power supply. The default is 'No' (disabled).

  • If set to 'Yes' and the loudspeaker is connected to a PoE+ Type 2 Class 4 capable power supply, the output is boosted and the Power > PoE+ control turns green.

  • If set to 'Yes' and the loudspeaker is not connected to a PoE+ Type 2 Class 4 capable power supply, the Power > PoE+ control is off and the Power > PoE control turns green.

  • If set to 'Yes' but the connected power supply fails to allocate full PoE+ power to the loudspeaker, the Status changes to Compromised.

Verbose

When set to 'Yes', a Details section appears in the control panel that displays device statistics and any errors, along with a Reset button to reset the statistics to zero.

Graphic Properties

Label

Use the Label property to change the name of the component in the schematic. The Label property defaults to the component name. To learn more about renaming schematic elements, see Organizing Your Design.

Position

The coordinates reference a specific place in the schematic - for example,"100,100" (horizontal, vertical). 0,0 is the upper left corner of the schematic.

Fill

Sets the fill color of the component in the schematic.

Script Access Properties

Code Name

Displays the currently assign name for control access. You can use the auto-assigned name or customize it. Q-SYS will automatically check all Code Names in the design to ensure name is unique.

Script Access

Defines whether the component will be accessible by script and/or externally, or not at all. Choices include All, External, None (default), and Script.

Tip: Use Script Programmer Mode to quickly view the Script Access setting directly on the component in the design schematic without the need to disconnect from the Q-SYS Core processor.

Status

ID

Click to flash the Status LED (yellow) under the NL Series loudspeaker grille, the LED Light Ring (yellow) on an NM Series microphone, or the ID LED (green) on the front of the QIO Series peripheral. The indicator flashes indefinitely until you press the ID button again.

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

  • OK: The device is functioning normally.
  • Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
  • Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
  • Missing: The device cannot be discovered.
  • Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
  • Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
  • Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

Clock Offset

This indicates how much of an offset exists, in microseconds, between the peripheral and the network Grandmaster. Not applicable to QIO Series Control I/O Expanders.

Grandmaster

This indicates the current clock master of the network. Not applicable to QIO Series Control I/O Expanders.

Parent Port

The clock Parent Port is the device and interface name to which the device is syncing. Typically, this is the Grandmaster. Not applicable to QIO Series Control I/O Expanders.

Processor Temp

The current temperature, in Celsius, of the peripheral's central processing unit.

Chassis Temp

For QIO Series Audio I/O Expanders only, this is the current temperature, in Celsius, of the device chassis.

Chassis Fan

For QIO Series Audio I/O Expanders only, this indicates the current RPMs of the device chassis fan.

Details

This section only appears when the Verbose property is set to 'Yes', and displays device statistics and any error conditions. Click Reset Details to clear the information.

Audio Stream

Note: This section appears only for NL Series peripherals.

Output Ok

This LED glows green when the QLAN audio stream is successfully being received by the loudspeaker.

Power

The controls shown in this section depend on the connected device. Not applicable to NM Series microphones.

Note: See the PoE+ Enable property description for more information.

PoE

Glows green if the loudspeaker is not connected to a PoE+ Type 2 Class 4 capable power supply.

PoE+

Glows green if the loudspeaker is connected to a PoE+ Type 2 Class 4 capable power supply.

PoE Active

Glows green when the device is connected to a PoE power supply.

DC Power

Glows green when the device is connected to a DC power supply.

Note: Available control pins depend on the specific peripheral model.

Pin Name

Value

String

Position

Pins Available

Chassis Fan RPM

n

n

-

Output

Chassis Temperature

n.n

 n.n°C -

Output

Clock Grandmaster Name

(text)

Output

Clock Offset From Master

 - nus -

Output

Clock Parent Port Name

(text)

Output

Disable RJ45 LED

0

1

false

true

0

1

Input / Output

DC Power Active

0

1

false

true

0

1

Output

Disable RJ45 LED

0

1

false

true

0

1

Input / Output

Identify

0

1

false

true

0

1

Input / Output

NL-[model] Status

NM-[model] Status

QIO-[model] Status

0

1

2

3

4

5

OK (Green)

Compromised (Orange)

Fault (Red)

Not Present (Gray)

Missing (Red)

Initializing (Blue)

-

Output

Output OK

0

1

false

true

0

1

Output

PoE+ Status

0

1

false

true

0

1

Output

PoE Active

0

1

false

true

0

1

Output

Processor Temperature

n.n

 n.n°C -

Output