PTZ-IP Conference Cameras

• Conference video for the Q-SYS AV-to-USB Bridging Solution
• Distribute video via the Q-LAN™ network anywhere it is needed
• Resolutions up to 1080p/60
• Image rotation controls to allow for inverted mounting
• Motorized Pan, Tilt and Zoom (PTZ) provides complete room coverage and privacy
• Auto Exposure, Auto Focus and Auto White Balance modes
• Native custom camera interfaces through Q-SYS Designer Software
• Includes wall mount for simple installation

Add the PTZ cameras to your design inventory from the Peripherals category. The following components are available for the PTZ-12x72 and PTZ-20x60:

• Status/Control

Front Panel

1. STATUS LED –
   • Green LED
   • Off indicates the camera is in STANDBY mode, network streams are off.
   • On indicates the camera is streaming video over the network.
   • Blinking indicates the ID mode is on
2. POWER LED -
   • Blue LED
   • On indicates the camera has power applied
   • Off indicates the camera has no power applied

Rear Panel

1. Label
   • Model: PTZ-12x72 or PTZ-20x60
   • MAC Address
   • Serial Number (on the bottom of the unit)
2. ID Button – Press to identify this piece of equipment in Q-SYS Designer, and Configurator. The green STATUS LED, on the front panel, blinks when in ID mode.
3. FACTORY RESET pin-hole – Use a paperclip or similar object to insert and press and hold the reset button for 5 seconds. This resets all parameters to the factory defaults.
4. Kensington™ Lock slot – Security cable not supplied.
5. LAN / POE – Q-SYS Gigabit Ethernet port / CAT5e or better / RJ45 / connect to the Q-LAN™ network switch with Power over Ethernet
6. HDMI – Camera output to various video formats setup by the users through Q-SYS Designer or a Q-SYS UCI (User Controlled Interface)

   Note: When a video format is selected, it is used by both the HDMI and 3G SDI outputs.

7. 3G SDI – Camera output to various video formats setup by the user. Setup is through Q-SYS Designer or a Q-SYS UCI
8. SERVICE – No user-accessible functionality.
9. DC 12 V – Connect an external power supply (not included). Supply to be rated at 12 V / 1 A, center-pin positive, outside barrel negative. Use only a Class 2 / LPS Power Supply.

	PTZ-12x72	PTZ-20x60
Image Sensor	1/2.7", Low Noise CMOS Image Sensor
Lens characteristics (wide to tele)
Optical zoom Horizontal Field of View Vertical Field of View	12x, f=3.5mm to 42.3mm, F1.8 to F2.8 72.5° to 6.9° 44.8° to 3.9°	20x, f=4.42mm to 88.5mm, F1.8 to F2.8 60.7 to 3.36° 34.1° to 1.89°
Minimal Illumination	0.5 lux at F1.8 (AGC On)
Noise Reduction	2D and 3D
S/N Ratio	≥ 55dB
Pan / Tilt Angle and Speed	Pan: ±170° rotation, speed: 1.7° to 100°/sec, Tilt: -30° to +90° rotation, speed: 1.7° to 69.9°/s
Ceiling Mountable	Image rotation for ceiling mounting set in Q-SYS Designer. Ceiling mount bracket accessory available.
HD Video Outputs	HDMI v1.3 and 3G-SDI
Ethernet	100BaseTX / 1000BaseT
Video Resolutions
HDMI / SDI: Network (30fps, 16:9):	1080p – 60/50/30/25 | 1080i – 60/50 | 720p – 60/50/30/25 1080p, 720p, 576p, 360p, 270p, 180p
Network Bandwidth	IP Stream 1, Motion JPEG: Up to 30Mbps per unicast IP stream IP Stream 2, H.264: Up to 2Mbps per unicast IP stream
Input Voltage	DC 12V / PoE (802.3af) Class 3
Current Consumption	1.0A (max)
Operating Temperature	-10°C - 40°C (14°F - 104°F), Indoor use only
Storage Temperature	-40°C - 60°C (-40°F - 140°F)
Power Consumption	12W (max)
Shipping Dimensions (H W D)	252mm x 235mm x 235mm (10in x 9.25in x 9.25in)
Weight
Shipping Camera	2.5kg (5.6lb) 1.4Kg (3.0lb)