Amp Output (DataPort Amplifiers)

Inputs

The inputs are digital audio connecting to loudspeaker components. Loudspeaker signal pins are represented by a left-pointing () triangle, and the wiring is represented by a thin orange line.

Outputs

The outputs are digital audio connecting to loudspeaker components. Loudspeaker signal pins are represented by a left-pointing () triangle, and the wiring is represented by a thin orange line.

Properties

Tip: For additional properties not listed, refer to the Properties Panel help topic for more information.

Amp Output Dataport Properties

Model

The Model of the amplifier - The Model is selected when you add an amplifier to Inventory, when you place the amplifier component in the Schematic, it retains the Model information. In the Properties you can change the Model if you need to.

Mode n-n¹

Choose if channels n and n are to be in the Stereo mode or the Bridged mode. This setting is to reflect the physical amplifier's setting.

¹The DataPort amplifiers support Bridged, Parallel and Stereo modes. Q-SYS supports amplifier modes Bridged and Stereo only. Parallel mode supplies the same signal to two channels by connecting both channel inputs to a single source. In Q-SYS, Parallel mode is accomplished by sending the same signal to two channels on the DataPort card. One DataPort cable carries two channels, so effectively there is no difference if you connect the channel inputs at the amplifier or in Q-SYS.

Controls

Amplifier Status

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

OK: The device is functioning normally.
Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
Missing: The device cannot be discovered.
Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

On / Standby

Button controls the amplifier from Standby to Power On.

Meter Select

Selects either RMS or Peak for the five meters in all channels.

Channel n Status

Mute

Mute button mutes the associated channel of the amplifier. Linked to the Mute button on the associated band of a loudspeaker.

Atten. Pot. (dB)

Setting of the Attenuation Potentiometer on the front panel of the amplifier.

Temperature

Temperature reading of the channel in - Centigrade.

Bridge

The amplifier must be connected and the On state for the Bridge and Parallel LEDs to work properly.

Yellow LED indicating that channel is in the Bridge Mode.

When this LED and the Parallel LED are off, the amplifier is in Stereo Mode. When they're both on, the amplifier is in Bridge-Parallel mode.

DAC Limit

LED indicating that signal to the D to A Converter is larger than can be reproduced and a limiter has been engaged to prevent clipping. This is an indication that the gain structure is not correct.

Protect

LED indicating that the channel is in Protect Mode. Usually due to attempting to drive too low an impedance for too long.

Clip

Yellow LED indicating that the channel is clipping.

Parallel ¹

The amplifier must be connected and the On state for the Parallel and Bridge LEDs to work properly.

Yellow LED indicating that channel is in the Parallel Mode.

When this LED and the Bridge LED are off, the amplifier is in Stereo Mode. When they're both on, the amplifier is in Bridge-Parallel mode.

¹When an amplifier is in Bridge Mode, the Parallel LED on the amplifier is lit along with the Bridge Mode LED. This LED is reflecting what is seen on the amplifier. See the note in the Properties table for Mode n-n.

Channel n Meter

Input (dBFS)

Measures the analog input to the amplifier channel (output of the DataPort card after the signal has been converted to analog). This reading can be RMS or Peak depending on the Meter Select setting for the associated channel.

The meter in the DataPort component displays the Peak Digital output before the D to A Converter.

Voltage (V)

Measures the voltage of the amplifier / loudspeaker circuit. This reading can be RMS or Peak depending on the Meter Select setting for the associated channel.

Current (A)

Measures the current of the amplifier / loudspeaker circuit. This reading can be RMS or Peak depending on the Meter Select setting for the associated channel.

Power (W)

Measures the power of the amplifier / loudspeaker circuit. This reading can be RMS or Peak depending on the Meter Select setting for the associated channel.

Headroom (dB)

Measures the amount of headroom left before reaching the amplifier's maximum capabilities.

Channel n Monitor

Listen

Enables and disables the loudspeaker monitor.

This is a radio type button and is linked to all other Listen buttons in your design. When this is engaged, all other Listen buttons disengage.

You can only listen to one amplifier channel at a time. In the loudspeaker components, you have the option to listen to one, all, or any combination of bands.

You must have the Loudspeaker Monitor component in the Schematic and properly connected to make use of the monitoring capability.

Note: The Monitor buttons are not linked in Emulate mode. Your design must be in Run mode for the functionality described above to operate.

Gain (dB)

Controls the gain of the monitor. This control has effect only when the Listen button is engaged.

Control Pins

The available Control Pins depend on settings in Properties.

Amplifier

Pin Name	Value	String	Position	Pins Available
Peak/RMS Select	0 1	Peak RMS	0 1	Input / Output
Power On	0 1	Standby On	0 1	Input / Output
Status	0 1 2 3 4	OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue)	0 0.250 0.500 0.750 1.00	Output

Pin Name

Value

String

Position

Pins Available

Peak/RMS Select

0

1

Peak

RMS

0

1

Input / Output

Power On

0

1

Standby

On

0

1

Input / Output

Status

0

1

2

3

4

OK (green)

Compromised (orange)

Fault (red)

Unknown (red)

Updating (blue)

0

0.250

0.500

0.750

1.00

Output

Channel

Pin Name	Value	String	Position	Pins Available
Attenuation Pot.	0 to 25 and Infinity	0 to 25, Infinity	0 26	Output
Bridge	0 1	false true	0 1	Output
Clip	0 1	false true	0 1	Output
Current	0 to 70	0 A to 70 A	0.000 1.000	Output
DAC Output Limit	0 1	false true	0 1	Output
Headroom	0 to 70	0 dB to 70 dB	0.000 1.000	Output
Input Meter	-100 to 20	-100 dB to 20 dB	0.000 1.000	Output
Monitor Gain	-100 to 20	-100 dB to 20 dB	0.000 1.000	Input / Output
Monitor Listen	0 1	disable enable	0 1	Input / Output
Mute	0 1	unmute mute	0 1	Input / Output
Parallel	0 1	false true	0 1	Output
Power	0 to 10000	0 W to 10,000 W	0.000 1.000	Output
Protect	0 1	false true	0 1	Output
Temperature	n	n °C	0.000 1.000	Output
Voltage	0 to 150	V to 150 V	0.000 1.000	Output

Amp Output (DataPort Amplifiers)

Inputs

Outputs

Amp Output Dataport Properties

Model

Mode n-n1

Amplifier Status

Status

On / Standby

Meter Select

Channel n Status

Mute

Atten. Pot. (dB)

Temperature

Bridge

DAC Limit

Protect

Clip

Parallel 1

Channel n Meter

Input (dBFS)

Voltage (V)

Current (A)

Power (W)

Headroom (dB)

Channel n Monitor

Listen

Gain (dB)

Amplifier

Channel

Mode n-n¹

Parallel ¹