Line Out (Core 110f, 110c)
The Mic/Line Out component provides eight channels of line-level output for devices other than QSC DataPort amplifiers. It is an integral part of Core 110 Series processors. The Line Out converts the processed digital signal to analog and provides software controls before and after the convertor. Connections are made using eight three-terminal 3.5mm Euro style connectors.
There are no adjustable properties for this component.
Each control listed in the Analog and Digital sections, are one per channel.
Analog
Peak Output Level (dBu)
Measures Peak Output level to the output device
Output Mute
Mutes the output after the D-A converter and before the output.
Max RMS Output Level (dBu)
Controls the analog RMS output level after the D/A converter. This level is typically set slightly lower than the destination's sensitivity or maximum input level in order to avoid clipping the signal of a power amplifier. Varies in direct proportion with Output Gain.
Output Gain (dB)
The amount of gain applied to the outgoing analog signal. Varies in direct proportion with the Max RMS Output Level.
Digital
Peak Output Level (dBFS)
Measures the Digital Signal level prior to the D/A converter.
Clip
Red LED indicating if the signal is being clipped.
Clip Hold
Holds the clip indication until manually cleared.
Invert
Inverts the audio signal.
Mute
Mutes the digital audio signal.
Gain (dB)
Controls the gain of the digital audio signal prior to the D/A converter.
Status
Status
Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:
- OK: The device is functioning normally.
- Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
- Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
- Missing: The device cannot be discovered.
- Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
- Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
- Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.
Pin Name |
Value |
String |
Position |
Pins Available |
---|---|---|---|---|
Analog Level |
-120 to 24 |
-120dB to 24dB |
0.000 to 1.00 |
Output |
Clip (LED) |
0 1 |
false true |
0 1 |
Output |
Clip Hold |
0 1 |
false true |
0 1 |
Input / Output |
Digital Level |
-120 to 43 |
-120dB to 43dB |
0.000 to 1.00 |
Output |
Gain |
-100 to 20 |
-100dB to 20dB |
0.000 to 1.00 |
Input / Output |
Invert |
0 1 |
normal invert |
0 1 |
Input / Output |
Max Level |
-40 to 21 |
-40.0dBu to +21dBu |
0 to .988 |
Input / Output |
Mute |
0 1 |
unmute mute |
0 1 |
Input / Output |
Output Gain |
-31 to 0 |
-31 dB to 0 dB |
0.000 to 1.00 |
Input / Output |
Output Mute |
0 1 |
unmute mute |
0 1 |
Input / Output |
Status |
0 1 2 3 4 |
OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue) |
0 0.250 0.500 0.750 1.00 |
Output |