Status (I/O-Core Nano)

A Q-SYS Core Nano is capable of operating simply as a peripheral I/O device. In this mode, you add the I/O-Core Nano from the Inventory, and then configure a separate Q-SYS Core processor to run your design. In Peripheral Mode, you can configure the same Serial Port and HID components as Core Mode.

Note: Loudspeaker Monitor and USB routing via the USB Input and USB Output components is not supported in Peripheral Mode for the Core Nano. HID Keyboard, HID Media, and HID Conferencing are supported.

Use Q-SYS Core Manager to switch a Q-SYS Core Nano to I/O-Core Nano mode. For more information, see Utilities in the Core Manager Help.

Note: After switching to I/O-Core Nano mode, use Q-SYS Configurator (within Q-SYS Designer Software) to discover and configure the device within the I/O Devices category. Selecting the I/O-Core Nano opens Peripheral Manager, which you can also use to change the mode back to Core Nano mode.

I/O Core Nano Properties

Name

The Name may contain ASCII letters 'a' through 'z' (case-insensitive), the digits '0' through '9', and the hyphen. Names cannot begin or end with a hyphen. No other symbols, punctuation characters, or blank spaces are permitted.

Note: This name must match the Hostname for the device as defined in Core Manager or Peripheral Manager.

Location

User-defined name that groups the component with other components in the same physical location – for example, "Rack 1" – or in the same organizational scheme.

Is Required

When enabled, and the device is not found on the network, the device is reported as 'Missing', which is an error condition. This is the default behavior. When disabled, and the device is not found on the network, the device is reported as 'Not Present', which is not an error condition.

Dynamically Paired

Indicates that this virtual component can be paired with the same type of hardware without changing the network ID of the hardware or the name of this component. Refer to the Q-SYS Core Manager Dynamic Pairing topic for more information. The default is 'No'.

Verbose

This property is only available when you select the I/O-510i Status component in your schematic. Select whether to expose Details (CPU statistics) and Audio Streams sections in the Status control panel.

External USB Audio

When enabled, you can connect an external audio device to the USB input and route audio to and from that device. See External USB Audio Device In and External USB Audio Device Out.

USB Bridging Properties

Refer to the USB Audio Bridge and USB Video Bridge topics.

Graphic Properties

Label

Use the Label property to change the name of the component in the schematic. The Label property defaults to the component name. To learn more about renaming schematic elements, see Organizing Your Design.

Position

The coordinates reference a specific place in the schematic - for example,"100,100" (horizontal, vertical). 0,0 is the upper left corner of the schematic.

Fill

Sets the fill color of the component in the schematic.

Script Access Properties

Code Name

Displays the currently assign name for control access. You can use the auto-assigned name or customize it. Q-SYS will automatically check all Code Names in the design to ensure name is unique.

Script Access

Defines whether the component will be accessible by script and/or externally, or not at all. Choices include All, External, None (default), and Script.

Tip: Use Script Programmer Mode to quickly view the Script Access setting directly on the component in the design schematic without the need to disconnect from the Q-SYS Core processor.

ID

Click to display the ID indicator on the I/O-Core Nano's front panel, as well as flash an indicator in Q-SYS Configurator next to the associated I/O-Core Nano. The front panel shows the ID indicator for 5 minutes unless you press the ID button again.

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

  • OK: The device is functioning normally.
  • Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
  • Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
  • Missing: The device cannot be discovered.
  • Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
  • Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
  • Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

Processor Temp.

The current temperature, in Celsius, of the I/O-Core Nano processor.

Chassis Temp.

The current temperature, in Celsius, of the I/O-Core Nano chassis.

Chassis Fan

Indicates the current RPMs of the I/O-Core Nano's chassis fan.

Details

This section only appears when the Verbose property is set to 'Yes', and displays any error conditions. Contact Support if you see any errors reported here. Click Reset Details to clear the information.

Network

Clock Master

LED indicating if the Core is the Master Clock for the Q-SYS system or not. The Core can be the Master Clock even if the clock is synchronized to an external clock.

Grandmaster

Displays either the Q-SYS Core processor name or the PTP Clock GUID. Note that:

  • There can only be one Grandmaster for a Q-SYS design (for all LAN interfaces of the device). It is possible for Q-SYS to resolve to a PTP Grandmaster present on LAN B, if enabled and present.
  • If available, the Core Name is displayed instead of the raw PTP clock GUID. (The Core Name is not available in some clocking topologies – for example, when a higher priority boundary clock between systems is present or with some Software Dante configurations, as when the Core syncs indirectly to another device via Software Dante’s boundary clock.)
  • A PTP Clock GUID can look similar to a MAC address, but is not the same and may not be related to a device’s actual MAC address.
  • If the PTP Clock GUID is derived from a MAC address (whether a Q-SYS Core processor or third-party device), it can be any MAC address on that device (any LAN interface, including those without a network connection).

PTPv1 (Dante)

Used specifically for Dante audio networking integration within the Q-SYS ecosystem

Clock Offset

Indicates how much of an offset exists, in microseconds, between the device and the network Grandmaster.

Parent Port

The clock Parent Port is the device and interface name to which the device is syncing. Typically, this is the Grandmaster.

Link

When the LED is lit, it means the interface is "UP," signifying that the network connection is active and functioning properly. Conversely, when the LED is not illuminated, it indicates that the interface is "DOWN," suggesting that there may be issues with the network connection.

IP Address

Displays the IP Address the Core is connected to.

Mode

Determines how device operates within the network environment.

Auto: The network interface automatically negotiates it settings with the network infrastructure.

Static: The network interface's settings are manually configured by the user, including the IP address, subnet mask, gateway, and other parameters.

Off: Disables the network interface, preventing it from sending or receiving network traffic.

PTPv2 State

Refers to the operational state or role of a network device or interface.

Passive: A device in the passive state is not actively transmitting or receiving data.

Slave: A device in the slave state is subordinate to another device, known as the master.

Master: A device in the master state holds authority or control over one or more slave devices in a network.

Uncalibrated: The uncalibrated state indicates a transition state between modes.

Speed

Refers to the data transfer rate supported by a network interface or connection. Speed indicates the transfer rate of megabits per second (Mbps).

Pin Name Value String Position Pins Available

Chassis Fan RPM

n

n

-

Output

Chassis Temperature

n.n

 n.n°C -

Output

Clock Grandmaster Name

(text)

Output

Clock Offset From Master

 - nus -

Output

Clock Parent Port Name

(text)

Output

Details

(text)

Output

I/O-Core Nano Status

0

1

2

3

4

5

OK (Green)

Compromised (Orange)

Fault (Red)

Not Present (Gray)

Missing (Red)

Initializing (Blue)

-

Output

Identify

0

1

false

true

0

1

Input / Output

Processor Temperature

n.n

 n.n°C -

Output

Reset Details

0

1

false

true

0

1

Input / Output