CXD-Q Amplifier Out Component

The CXD-Q Amplifier Out component is used to send audio over Q-LAN, to the CXD-Q output channels. This component provides the inputs to the output stage of the amplifier. All audio sent to the amplifier output section is from this component via Q-LAN. The Line Inputs on the rear of the amplifier are converted to digital audio and sent to the CXD-Q Input component via Q-LAN.

Amplifiers are added to the Inventory list based on the physical amplifiers in your system. Each amplifier in the Inventory list has Components associated with it that are placed in the Schematic for configuration and wiring. The CXD-Q Out Control Panel is used for telemetry, and control of the On/Standby button, the Mute buttons, Gain controls. The same controls are available on the amplifier's front panel.

Inputs

The inputs are digital audio from any appropriate component within Q-SYS Designer. There can be from one to four inputs depending on the FAST configuration.

Outputs

The outputs are digital audio connecting to loudspeaker components.

70V, 100V Mode

The CXD-Q amplifiers are capable of supplying 70V or 100V outputs. In order to use this mode, you must connect an appropriate loudspeaker component to the CXD-Q Out component. For QSC loudspeaker components, capable of using 70V or 100V, set the Mode Property of the component to either 70V or 100V. Q-SYS sets the amplifier to this mode when the design is deployed.

In addition, when an amplifier is set to either 70V or 100V mode, a 50 Hz high-pass filter is automatically added in line to protect the loudspeakers.

CXD4.2Q

In order to set the CXD4.2Q amplifiers to 70V or 100V mode you must configure the outputs to channels A and B bridged, and channels C and D bridged (A+B C+D).

Controls

The controls listed below are divided into sections to match the Control Panel sections.

Once you establish the initial settings for a component, you can save those settings, along with all the other component's settings, in a Snapshot.

Amplifier Status

Control	Function	Default/Range
Status	Displays the current status of the amplifier both in text and color. The following is a list of possible status colors, and some example conditions. OK – Green – (0) – Audio is good, hardware is good. Compromised – Orange – (1) – Audio is good but a redundancy mechanism is active (one LAN down but the other is still up) or a non-fatal hardware problem exists (fans too slow, temperature higher than expected, etc.) Fault – Red – (2) – Audio is not passing, or hardware is malfunctioning or mis-configured (amplifier power off, audio streams broken, wrong type of I/O Card installed, loudspeaker short circuit, etc.) Missing – Red – (3) – A piece of hardware, defined in the design, has not been discovered. Audio is not passing through that piece of hardware. Initializing – Blue – (5) – In the process of firmware, configuration update, and design start. Audio is obviously bad. Not Present – Gray – A virtual component in the design, that is designated as Dynamically Paired, and Not Required ,has no hardware assigned to it.	N/A
On/Standby	Button controls the amplifier from Standby to Power On and back.	Standby Power On
Mute All	Mutes all channels of the amplifier. Once Mute All is engaged, you must use the Mute All button to unmute the channels. The individual channel Mute is disabled while the Mute All is engaged.	Mute/Unmute
Gain Lock	Disables the gain control on the front panel of the amplifier. The gain controls in the Q-SYS Designer component are not disabled.	Disabled/Enabled
Mute Lock	Disables the mute controls on the front panel of the amplifier. The mute controls in the Q-SYS Designer component are not disabled.	Disabled/Enabled
AC Voltage	The AC Mains voltage.	100 VAC to 240 VAC
AC Current	The AC Mains current being drawn by the amplifier.
PSU Temp	Temperature of the amplifier's power supply.	55° C = Compromised State 63° C Mutes Audio
Ch A&C Temp	The temperature for channels A and C combined.	80° C = Mutes Outputs
Ch B&D Temp	The temperature for channels B and D combined.	80° C = Mutes Outputs
V Rail 1	Internal amplifier voltage monitor.	147VDC +/- 5V typical
V Rail 2	Internal amplifier voltage monitor.	-147VDC +/- 5V typical
Fan RPM	The fan speed varies based on the temperatures.	–
Meter Select	Selects either RMS or Peak for the five meters in all channels. Changing the meter type changes the meter readings on the CXD-Q Out component and on the amplifier output gain meters.	RMS/Peak
Standalone (test button)	Press this button to simulate Standalone mode. You will hear the audio that is played when the amplifier is in the Standalone Mode.	Off / On

Channel (A, B, C, D) Status

Control	Function	Default/Range
Channel	The channel letter changes based on the FAST™ (Flexible Amplifier Summing Technology) selection in the Properties. Single channels = A (or B, C, D) Parallel channels = AB (or CD) Bridged channels = A+B (or C+D) Refer to Properties "FAST Mode"	Default = Four separate channels – A, B, C, D
Mute	Mute button mutes the associated channel of the amplifier. Linked to the Mute button on the amplifier.	Off / On
DAC Limit	LED indicating that signal to the D to A Converter is larger than can be reproduced and a limiter has been engaged to prevent clipping. This is an indication that the gain structure is not correct.	False/True
Protect	LED indicating that the channel is in Protect Mode. Usually due to attempting to drive too low an impedance for too long.	False/True
Clip	Red LED indicating that the channel is clipping.	False/True
Limit	Red LED indicating that the amplifier is in the limiting mode.	False/True

Channel (A, B, C, D) Meter

These readings can be RMS or Peak depending on the Meter Select setting.

Control	Function	Default/Range
Input (dBFS)	Measures the digital input to the amplifier output channel.	Range = -100 to 20
Voltage (V)	Measures the voltage of the amplifier / loudspeaker circuit.	Range = 0 - 150
Current (A)	Measures the current of the amplifier / loudspeaker circuit.	N/A
Power (W)	Measures the power of the amplifier / loudspeaker circuit.	N/A
Headroom (dB)	Measures the amount of headroom left before reaching the amplifier's maximum capabilities.	N/A

Monitor

There is one Listen button and one Gain control for each channel.

Control	Function	Default/Range
Listen	Measures the digital input to the amplifier output channel.	Range = -100 to 20
Gain (V)	Measures the voltage of the amplifier / loudspeaker circuit.	Range = 0 - 150

Control

Function

Default/Range

Listen

Measures the digital input to the amplifier output channel.

Range = -100 to 20

Gain

(V)

Measures the voltage of the amplifier / loudspeaker circuit.

Range = 0 - 150

Standalone

There is one Mute button and one Gain control for each channel.

Control	Function	Default/Range
Mute	Mutes the output of the amplifier channel when in Standalone Mode.	Off/On
Gain (dB)	Controls the Gain of the amplifier's output when in Standalone mode.	Default = 0 Range = -100 to 20

Control

Function

Default/Range

Mute

Mutes the output of the amplifier channel when in Standalone Mode.

Off/On

Gain

(dB)

Controls the Gain of the amplifier's output when in Standalone mode.

Default = 0

Range = -100 to 20

Properties

Refer to the CXD-Q Amplifier Status Component topic Properties.

Control Pins

The available Control Pins depend on settings in Properties.

Amplifier

Pin Name	Value	String	Position	Pins Available
AC Current				Output
AC Mains Voltage	100 - 240	100V - 240V	0V = 0 120V = .5 240V = 1.00	Output
Channel A&C Temperature	n	n °C	0.000 1.000	Output
Channel A&C Temperature	n	n °C	0.000 1.000	Output
Fan Speed
Gain Lockout	0 1	disabled enabled	0 1	Input / Output
Mute All	0 1	unmute mute	0 1	Input / Output
Mute Lockout	0 1	disabled enabled	0 1	Input / Output
Peak/RMS Select	0 1	Peak RMS	0 1	Input / Output
Power On	0 1	Standby On	0 1	Input / Output
Power Supply Temp	n	n °C	0.000 1.000	Output
Rail 1 Voltage	142 to 152	142V to 152V	0.000 1.000	Output
Rail 2 Voltage	-142 to -152	-142V to -152V	0.000 1.000	Output
Status	0 1 2 3 4	OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue)	0 0.250 0.500 0.750 1.00	Output

Channel

Pin Name	Value	String	Position	Pins Available
Current	0 to 70	0 A to 70 A	0.000 1.000	Output
DAC Output Limit	0 1	false true	0 1	Output
Gain	-100 to 20	-100 dB to 20 dB	0.000 1.000	Input / Output
Headroom	0 to 70	0 dB to 70 dB	0.000 1.000	Output
Input Meter	-100 to 20	-100 dB to 20 dB	0.000 1.000	Output
Limit	0 1	false true	0 1	Output
Monitor Gain
Monitor Listen	0 1	disabled enabled	0 1	Input / Output
Mute	0 1	unmute mute	0 1	Input / Output
Power	0 to 10000	0 W to 10,000 W	0.000 1.000	Output
Protect	0 1	false true	0 1	Output
Voltage	0 to 150	V to 150 V	0.000 1.000	Output