Network Services

Depending on the MIB browser you select, you can access the Q-SYS information using SNMP v2c and/or SNMP v3.

Note: The parameters you specify in Q-SYS Core Manager must be the same values you specify in the MIB browser.

Click Edit to modify SNMP access parameters.

Version 2C

• Access: Select SNMP v2c access is Disabled, Read Only, or Read/Write.
• Community: Specify the v2c community text string.

Version 3

• Access: Select whether SNMP v3 access is Disabled, Read Only, or Read/Write.
• User: The SNMP v3 username string.
• Security Level: Select from:
  • No Authorization – Only a username is required.
  • Authorization No Privacy – Requires a password, and allows selection of an Auth Protocol.
  • Authorization and Privacy – Adds another layer of security using a Privacy Password and Encryption.
• Password: The password for authorization, which is encrypted and masked. The password must be a minimum of 8 characters.
• Auth Protocol: The protocol for encrypting the signature attached to the SNMP message, either MD5 or SHA.
• Privacy Password: This password is used with the 'Authorization and Privacy' security level, which encrypts the entire SNMP message. The password is encrypted and masked, and must be a minimum of 8 characters.
• Encryption: Select an encryption type, either DES or AES.

Load the Q-SYS MIB into a MIB browser to access the Q-SYS SNMP objects by name. You can put the MIB anywhere as long as the MIB browser has access to the location.

You can obtain the MIB file from:

• The Q-SYS Designer installation directory: C:\Program Files\QSC\Q-SYS Designer\SNMP
• The QSC website (https://www.qsc.com) – search for "MIB".

• NET-SNMP-MIB
• NET-SNMP-FRAMEWORK-MIB
• NET-SNMP-EXTEND-MIB
• SNMPv2-MIB
• SNMP-MPD-MIB
• SNMP-USER-BASED-SM-MIB
• SNMP-VIEW-BASED-ACM-MIB
• UCD-SNMP-MIB
• UCD-DLMOD-MIB

Each device in the Q-SYS design's Inventory has an entry with the following objects:

• invDeviceName (Read Only) – the name of the Inventory device
• invDeviceType (Read Only) – the type of Inventory device (Core, Peripheral, Page Station, Amplifier, etc. )
• invDeviceModel (Read Only) – the specific model of the Inventory device
• invDeviceLocation (Read Only) – the Location of the Inventory device
• invDeviceStatus (Read Only) – the Status string
• invDeviceStatusValue (Read Only) – the Status value. (See See Status Reference for possible values.)

Each Snapshot Bank has an entry with the following objects:

• ssSnapshotName (Read Only) – the Name of the Snapshot Bank.
• ssSsTotalSnapshots (Read Only) – the total available snapshots in the Snapshot Bank.
• ssActiveSnapshot (Read/Write) – Sets the active Snapshot.
• ssRampTimeSec (Read/Write) – Sets the time it takes for the controls to reach the saved position or value (in seconds).

Note: For all other Q-SYS SNMP objects, see MIB file.

In situations where multiple Cores are connected to the corporate network for control and monitoring only, Q-SYS Audio Enabled Peripherals should be disabled on LAN B. This will stop the Core from behaving as a PTP boundary clock and will solve problems related to Cores attempting to PTP sync over a potentially non-real-time-capable network infrastructure.

Running older designs with the 'PTPv2 Disable LAN B' design property enabled

The Q-SYS Audio Enabled Peripherals network service includes the PTPv2 protocol. In Q-SYS Designer versions prior to 7.1, this protocol could be disabled for LAN B in the Design Properties. If you attempt to save a design to the Core with this property enabled, you will be prompted to disable Q-SYS Audio Enabled Peripherals for LAN B in the Network Services manager if this network service is currently enabled on LAN B.

Note: Alternatively, you can choose to clear the PTPv2 Disable design property and run your design without configuring Network Services. Doing so is not recommended unless you explicitly require the design to allow PTPv2 traffic on both LAN A and LAN B – for example, for redundant networking, or third party devices configured for LAN A and LAN B connections.

If LAN B (or AUX) is connected to the corporate network, you may want to disable Q-SYS Device Discovery, Q-SYS Audio Enabled Peripherals, and Q-SYS Control Peripherals for LAN B / AUX to "lock down" Q-SYS devices from the corporate network. However, to still allow UCI viewers (Windows and iOS) to communicate with the Core from the corporate network, you could enable Q-SYS UCI Viewers for LAN B / AUX exclusively.

Note: If device discovery is disabled, Hard Links must be used to locate the Q-SYS Core on the network.

If you have a Core and touchscreen and are only using the built-in audio on the Core, you could disable Q-SYS Audio Enabled Peripherals for all network adapters but keep Q-SYS Control Peripherals enabled.

If your design does not use any TSC-3 touchscreens, you could disable the Q-SYS TSC-3 network service, which disables the FTP protocol on the Core.

If your system does not require control from a third-party control system, consider disabling the Q-SYS External Control Protocol (ASCII and JSONRPC) on all network interface ports.

• If your design does not use Network Redundancy, you could disable LAN B / AUX for all network services.
• If your design uses Core Redundancy, ensure that both the Primary Core and Backup Core network services are configured the same.