Network > Services
Manage the Q-SYS Core processor's ability to communicate with devices through its network interfaces. System administrators can:
- Disable unused network services on a per-network adapter level (LAN A, LAN B, AUX LAN, etc.). Disabling unused network services can increase the security of the Q-SYS system and help to satisfy customer-specific security requirements.
- Easily see a summary of all currently-enabled network services and protocols, per network adapter, on the Core.
CAUTION: By default, all network services are enabled on the Core. QSC recommends disabling unneeded network services.
Audit
The Audit tab provides a read-only listing of all active network protocols on the Core and the network adapters on which they are enabled.
For any active network protocol, click + to see a list of the network services using that particular protocol.
Management
The Management tab provides a list of high-level network services on the Core. A check mark indicates if a network service is active for a particular LAN adapter.
- Click Edit to enable or disable (select or deselect) a network service for a LAN adapter, and then click Save.
Note: Some network services can only be toggled on or off for all LAN adapters at once.
- Click + to expand a high-level network service to see a list of protocols used by that service.
- In the Filter by Protocol section, you can easily see a summary of protocol usage on the Core. The number next to the protocol name indicates how many network services are using that protocol across all LAN adapters. For example:
Tip: Click a protocol name to filter the High-Level Network Services list to show only those services that use the selected protocol. To turn the filter off, click the protocol name again.
Use Cases and Recommendations
Software Dante requires the mDNS protocol. Before running a design that includes Software Dante components, you must enable the Q-SYS Device Discovery via mDNS / Bonjour network service for the LAN interfaces you are using for Software Dante. LAN interfaces for Software Dante are configured in File > Design Properties in Q-SYS Designer Software.
If your deployment requires disabling port 80 for security reasons, then disable the Q-SYS Designer Communications - Legacy network service on the LAN adapter you intend to secure (LAN A, LAN B, AUX LAN, etc.). This network service allows for communication between the Core and Q-SYS Designer software v7.1 or earlier. Cores running v7.2 firmware or higher have HTTPS (port 443) enabled by default as a secure alternative to this service. Therefore, it is no longer required unless you intend to downgrade the Core's firmware to v7.1 or lower.
In situations where multiple Cores are connected to the corporate network for control and monitoring only, Q-SYS Audio Enabled Peripherals should be disabled on LAN B. This will stop the Core from behaving as a PTP boundary clock and will solve problems related to Cores attempting to PTP sync over a potentially non-real-time-capable network infrastructure.
Running older designs with the 'PTPv2 Disable LAN B' design property enabled
The Q-SYS Audio Enabled Peripherals network service includes the PTPv2 protocol. In Q-SYS Designer versions prior to 7.1, this protocol could be disabled for LAN B in the Design Properties. If you attempt to save a design to the Core with this property enabled, you will be prompted to disable Q-SYS Audio Enabled Peripherals for LAN B in the Network Services manager if this network service is currently enabled on LAN B.
Note: Alternatively, you can choose to clear the PTPv2 Disable design property and run your design without configuring Network Services. Doing so is not recommended unless you explicitly require the design to allow PTPv2 traffic on both LAN A and LAN B – for example, for redundant networking, or third party devices configured for LAN A and LAN B connections.
If LAN B (or AUX) is connected to the corporate network, you may want to disable Q-SYS Device Discovery, Q-SYS Audio Enabled Peripherals, and Q-SYS Control Peripherals for LAN B / AUX to "lock down" Q-SYS devices from the corporate network. However, to still allow UCI viewers (Windows and iOS) to communicate with the Core from the corporate network, you could enable Q-SYS UCI Viewers for LAN B / AUX exclusively.
Note: If device discovery is disabled, Hard Links must be used to locate the Core on the network.
If you have a Core and touchscreen and are only using the built-in audio on the Core, you could disable Q-SYS Audio Enabled Peripherals for all network adapters but keep Q-SYS Control Peripherals enabled.
If your system does not require control from a third-party control system, consider disabling the Q-SYS External Control Protocol (ASCII and JSONRPC) on all network interface ports.
If your design does not use Network Redundancy, you could disable LAN B / AUX for all network services.
If your design uses Core Redundancy:
- Ensure that the Q-SYS Core Redundancy network service is enabled on both the Primary Core and Backup Core. This service is required if Core Redundancy is configured in the Q-SYS design file.
- Ensure that all network services for both the Primary Core and Backup Core are configured the same.
If your design does not use Core Redundancy, you could disable the Q-SYS Core Redundancy network service for all LAN interfaces.
Notes
- Some protocols are used by multiple network services – for example, Q-SYS Discovery Protocol (QDP). A protocol remains active on the Core until all network services using it are disabled for a particular LAN adapter.
- The Q-SYS Designer Communications - Secure network service uses self-signed, encrypted HTTPS communications between the Core and Q-SYS Designer, so is active on all network ports at all times.
- To avoid issues, ensure that design-specific settings (such as Core Redundancy) are compatible with the Core's Network Services configuration.