Flex Out (I/O-8 Flex)
The I/O-8 Flex provides eight audio channels that can be individually switched between line inputs and line outputs. The I/O-8 Flex Output Component provides the control and selection of the line-level outputs on the I/O-8 Flex. The Flex Output component converts the processed digital signal to analog and provides software controls before and after the convertor. Connections are made using three-terminal 3.5mm Euro style connectors.
Note: The Flex Input and Output components are not for use with QSC DataPort amplifiers.
Controls
Each control listed in the Analog and Digital sections, are one per channel.
Flex I/O
Control |
Function |
Default / Range |
---|---|---|
Output |
Changes the associated channel to a Flex Output channel. To switch back to a Flex Input channel, you must enable the channel in the Flex Input component. |
Default = disabled Range = disabled / enabled |
Analog
Control |
Function |
Default / Range |
---|---|---|
Peak Output Level (dBu) |
Measures Peak Output level to the output device. |
N / A |
Output Mute |
Mutes the output after the D-A converter and before the output. |
Off / On |
Max RMS Output Level (dBu) |
Controls the analog RMS output level after the D/A converter. This level is typically set slightly lower than the destination's sensitivity or maximum input level in order to avoid clipping the signal of a power amplifier. Varies in direct proportion with Output Gain. |
Default = +12 Range = -40 to +12 |
Output Gain (dB) |
The amount of gain applied to the outgoing analog signal. Varies in direct proportion with the Max RMS Output Level. |
Default = 0 Range = -52 to 0 |
Digital
Control |
Function |
Default / Range |
---|---|---|
Peak Output Level (dBFS) |
Measures the Digital Signal level prior to the D/A converter. |
N / A |
Clip |
Red LED indicating if the signal is being clipped. |
Off / On |
Clip Hold |
Holds the clip indication until manually cleared. |
Off / On |
Invert |
Inverts the audio signal. |
Off / On |
Mute |
Mutes the digital audio signal. |
Off / On |
Gain (dB) |
Controls the gain of the digital audio signal prior to the D/A converter. |
Default = 0 Range = -100 to +20 |
Status
Control |
Function |
Default / Range |
---|---|---|
Status |
Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:
|
N / A |
Properties
There are no adjustable properties for the Flex Output component.
Control Pins
Pin Name |
Value |
String |
Position |
Pins Available |
---|---|---|---|---|
Analog Level |
-120 to 20 |
-120 dB to 20 dB |
0.000 to 1.00 |
Output |
Clip |
0 1 |
false true |
0 1 |
Output |
Clip Hold |
0 1 |
false true |
0 1 |
Input / Output |
Digital Level |
-100 to 20 |
-100 dB to 20 dB |
0.000 to 1.00 |
Output |
Flex Output Enable |
0 1 |
false true |
0 1 |
Input / Output |
Gain |
-100 to 20 |
-100 dB to 20 dB |
0.000 to 1.00 |
Input / Output |
Invert |
0 1 |
normal invert |
0 1 |
Input / Output |
Max Level (dBu) |
-40 to 20 |
-40.0 to 20 |
0 to .988 |
Input / Output |
Mute |
0 1 |
unmute mute |
0 1 |
Input / Output |
Output Gain |
-31 to 0 |
-31 dB to 0 dB |
0.000 to 1.00 |
Input / Output |
Output Mute |
0 1 |
unmute mute |
0 1 |
Input / Output |
Status |
0 1 2 3 4 |
OK (green) Compromised (orange) Fault (red) Unknown (red) Updating (blue) |
0 0.250 0.500 0.750 1.00 |
Output |