Line Out (NV-32-H)
The NV-32-H (Core Capable) and NV-32-H include a 3.5mm phone-style (round) Audio Out jack for connection of stereo audio equipment, such as a computer's Line In jack. The Line Out component converts the processed digital signal from Q-SYS to analog audio.
Use the Line Out component to configure both the source digital signal from Q-SYS and the outgoing analog signal to connected equipment.
The Line Out component represents the AUDIO OUT jack on the rear of the NV-32-H.
Input Pins
Channel 1, 2
Each pin represents one channel of stereo audio to send from Q-SYS to connected analog equipment:
- Channel 1: Left side audio.
- Channel 2: Right side audio.
Output Pins
This component has no output pins.
See the HDMI I/O (NV-32-H) topic for a list of available Network Video Endpoint Properties.
Analog
Peak Output Level (dBu)
The peak audio level to the output device, from -120 to 24 dBu.
Output Mute
Click to mute the output after the D-A converter and before the output to the device.
Max RMS Output Level
Set the analog RMS output level after the D/A converter, from -60 to +4 dBu (default is +4). To avoid clipping the signal of a power amplifier, you typically set this level slightly lower than the destination's sensitivity or maximum input level.
This level varies in direct proportion with Output Gain.
Output Gain
Adjust the amount of gain applied to the outgoing analog signal, from -64 to 0 dB (default is 0).
This level varies in direct proportion with Max RMS Output Level.
Digital
Peak Output Level (dBFS)
Measurement of the digital signal level prior to the D/A converter, from -120 to 43 dB.
- Green = good
- Yellow = close to clipping
- Red = clipping
Clip
LED indicates if the incoming signal is being clipped.
Clip Hold
Click to hold the clip indication until you manually clear it.
Invert
Click to invert the polarity of the incoming digital audio signal from Q-SYS.
Mute
Click to mute the incoming digital audio signal from Q-SYS.
Gain
Click to adjust the gain of the audio signal from Q-SYS, from -100 dB to 20 dB (default is 0).
Status
Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:
- OK: The device is functioning normally.
- Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
- Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
- Missing: The device cannot be discovered.
- Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
- Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
- Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.
Pin Name |
Value |
String |
Position |
Pins Available |
---|---|---|---|---|
Status |
0 1 2 3 4 5 |
OK (Green) Compromised (Orange) Fault (Red) Not Present (Gray) Missing (Red) Initializing (Blue) |
- |
Output |
Channel 1, 2 |
||||
Clip |
0 1 |
false true |
0 1 |
Output |
Clip Hold |
0 1 |
false true |
0 1 |
Input / Output |
Gain |
-100 to 20 |
-100dB to 20dB |
0.000 to 1.00 |
Input / Output |
Invert |
0 1 |
normal invert |
0 1 |
Input / Output |
Level (dBFS) |
-120 to 43 |
-120dB to 43dB |
0.000 to 1.00 |
Output |
Level (dBu) |
-120 to 24 |
-120dB to 24dB |
0.000 to 1.00 |
Output |
Max Level |
-60 to 4 |
-60dBu to +4dBu |
0 to .988 |
Input / Output |
Mute |
0 1 |
unmute mute |
0 1 |
Input / Output |
Output Gain |
-64 to 0 |
-64dB to 0dB |
0.000 to 1.00 |
Input / Output |
Output Mute |
0 1 |
unmute mute |
0 1 |
Input / Output |