Digital In – DCIO/DCIO-H

This component has no configurable properties.

HDMI (DCIO-H only)

HDMI Enable

Click to enable or disable HDMI functionality. When this is activated, the AES channels 9 through 16 are disabled and become HDMI channels.

Note: The HDMI Enable and AES 9-16 Enable are radio-type buttons. Both cannot be in the same position at the same time.

Audio Format

The format of the detected audio input.

Sample rate

The sample rate of the detected audio input.

Upmix

Select whether to upmix HDMI stereo audio content to synthesize a center channel, as well as side and rear surround channels. Options include None (default), 5.1, and 7.1:

	Upmix Control Selection
Format of Input Audio	None	5.1	7.1
Stereo1	Stereo	7.0	7.0
Lt/Rt (Surround-encoded stereo)1	5.0 / 7.0	5.0 / 7.0	5.0 / 7.0
5.1	5.1	5.1	7.1
7.1	7.1	7.1	7.1

1. LFE not supported.

LEDs

An LED is illuminated when there is a signal available on that channel: L (left), R (right), C (center), LFE (low frequency extension), Ls (left surround), Rs (right surround), Lb (left back), Rb (right back).

AES (DCIO-H only)

AES 9-16 Enable

Click to enable or disable AES functionality for channels 9 through 16. When this is activated, the HDMI functionality is disabled.

Note: The HDMI Enable and AES 9-16 Enable are radio-type buttons. Both cannot be in the same position at the same time.

Input (for DCIO-H) / AES (for DCIO)

Peak Input Level (dBFS)

Graphic display of the peak input level to the AES3 and / or the HDMI Input, measured in dBFS.

Digital

Invert

Inverts the input signal.

Mute

Mutes the input signal.

Gain

Sets the gain of the input signal, from -100 to 20dB (default is 0).

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

• OK: The device is functioning normally.
• Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
• Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
• Missing: The device cannot be discovered.
• Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
• Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
• Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

Pin Name	Value	String	Position	Pins Available
Channel (1 through 16)
Gain	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Input / Output
Invert	0 1	normal invert	0 1	Input / Output
Level (Peak Input Level (dBFS))	-100 to 20	-100 dB to 20 dB	0.000 to 1.00	Output
Mute	0 1	unmute mute	0 1	Input / Output
AES Input 9-16 Enable	0 1	disable enable	0 1.00	Input / Output
Channel Status C	0 1	false true	0 1.00	Output
Channel Status L	0 1	false true	0 1.00	Output
Channel Status Lb	0 1	false true	0 1.00	Output
Channel Status LFE	0 1	false true	0 1.00	Output
Channel Status Ls	0 1	false true	0 1.00	Output
Channel Status R	0 1	false true	0 1.00	Output
Channel Status Rb	0 1	false true	0 1.00	Output
Channel Status Rs	0 1	false true	0 1.00	Output
HDMI Audio Format	0 1	false true	0 1.00	Output
HDMI Index	0 1	false true	0 1.00	Output
HDMI Audio Samplerate	N / A	text-kHz	N / A	Output
HDMI Audio Upmix	-	None 5.1 7.1	-	Input / Output
HDMI Input Enable	0 1	disable enable	0 1.00	Input / Output
Status	N / A	Text	N / A	Output