Network > SNMP
SNMP allows you to manage and/or monitor devices on the Q-LAN network for conditions that may need attention. With a third-party Management Information Base (MIB) browser, you can poll any Q-SYS Core, which returns its status as well as the status of any Q-SYS peripheral devices included in the running design. Additionally, third-party devices monitored via Q-SYS Reflect-enabled plugins or the Monitoring Proxy component also report their statuses via the Core using SNMP.
Note: SNMP is disabled by default on new Q-SYS Core processors and those that have been factory reset.
Configuring SNMP Access
Depending on the MIB browser you select, you can access the Q-SYS information using SNMP v2c and/or SNMP v3.
Note: The parameters you specify in Network Services > SNMP must be the same values you specify in the MIB browser.
Click Edit to modify SNMP access parameters.
Version 2C
- Access: Select SNMP v2c access is Disabled, Read Only, or Read/Write.
- Community: Specify the v2c community text string.
Version 3
- Access: Select whether SNMP v3 access is Disabled, Read Only, or Read/Write.
- User: The SNMP v3 username string.
- Security Level: Select from:
- No Authorization – Only a username is required.
- Authorization No Privacy – Requires a password, and allows selection of an Auth Protocol.
- Authorization and Privacy – Adds another layer of security using a Privacy Password and Encryption.
- Password: The password for authorization, which is encrypted and masked. The password must be a minimum of 8 characters.
- Auth Protocol: The protocol for encrypting the signature attached to the SNMP message, either MD5 or SHA.
- Privacy Password: This password is used with the 'Authorization and Privacy' security level, which encrypts the entire SNMP message. The password is encrypted and masked, and must be a minimum of 8 characters.
- Encryption: Select an encryption type, either DES or AES.
Loading the MIB File
Load the Q-SYS MIB into a MIB browser to access the Q-SYS SNMP objects by name. You can put the MIB anywhere as long as the MIB browser has access to the location.
You can obtain the MIB file from:
- The Q-SYS Designer installation directory:
C:\Program Files\QSC\Q-SYS Designer\SNMP - The QSC website (https://www.qsc.com) – search for "MIB".
Supported Third-Party MIBs
- NET-SNMP-MIB
- NET-SNMP-FRAMEWORK-MIB
- NET-SNMP-EXTEND-MIB
- SNMPv2-MIB
- SNMP-MPD-MIB
- SNMP-USER-BASED-SM-MIB
- SNMP-VIEW-BASED-ACM-MIB
- UCD-SNMP-MIB
- UCD-DLMOD-MIB
Inventory Table
Each device in the Q-SYS design's Inventory has an entry with the following objects:
- invDeviceName (Read Only) – the name of the Inventory device
- invDeviceType (Read Only) – the type of Inventory device (Core, Peripheral, Page Station, Amplifier, etc. )
- invDeviceModel (Read Only) – the specific model of the Inventory device
- invDeviceLocation (Read Only) – the Location of the Inventory device
- invDeviceStatus (Read Only) – the Status string
- invDeviceStatusValue (Read Only) – the Status value. (See Status for possible values.)
Snapshot Table
Each Snapshot Bank has an entry with the following objects:
- ssSnapshotName (Read Only) – the Name of the Snapshot Bank.
- ssSsTotalSnapshots (Read Only) – the total available snapshots in the Snapshot Bank.
- ssActiveSnapshot (Read/Write) – Sets the active Snapshot.
- ssRampTimeSec (Read/Write) – Sets the time it takes for the controls to reach the saved position or value (in seconds).
Note: For all other Q-SYS SNMP objects, see the MIB file.
