Analog In – DCIO/DCIO-H

DCIO-H Properties Analog In

Name

The Name may contain ASCII letters 'a' through 'z' (case-insensitive), the digits '0' through '9', and the hyphen. Names cannot begin or end with a hyphen. No other symbols, punctuation characters, or blank spaces are permitted.

Note: This name must match the Hostname for the device as defined in Core Manager or Peripheral Manager.

Location

User-defined name that groups the component with other components in the same physical location – for example, "Rack 1" – or in the same organizational scheme.

Is Network Redundant

Select whether the device is connected to redundant networks.

Is Required

When enabled, and the device is not found on the network, the device is reported as 'Missing', which is an error condition. This is the default behavior. When disabled, and the device is not found on the network, the device is reported as 'Not Present', which is not an error condition.

Dynamically Paired

Indicates that this virtual component can be paired with the same type of hardware without changing the network ID of the hardware or the name of this component. Refer to the Q-SYS Core Manager Dynamic Pairing topic for more information. The default is 'No'.

Graphic Properties

Label

Use the Label property to change the name of the component in the schematic. The Label property defaults to the component name. To learn more about renaming schematic elements, see Organizing Your Design.

Position

The coordinates reference a specific place in the schematic - for example,"100,100" (horizontal, vertical). 0,0 is the upper left corner of the schematic.

Fill

Sets the fill color of the component in the schematic.

Script Access Properties

Code Name

Displays the currently assign name for control access. You can use the auto-assigned name or customize it. Q-SYS will automatically check all Code Names in the design to ensure name is unique.

Script Access

Defines whether the component will be accessible by script and/or externally, or not at all. Choices include All, External, None (default), and Script.

• None (default) - Not accessible by any script, plugin, or by Q-SYS Remote Control Protocol (QRC).
• Script - Can be accessed by scripts, such as Text Controller, Block Controllers, and plugins only.
• External - Can only be accessed by 3rd party controls systems using component commands from the Q-SYS Remote Control Protocol (QRC).
• All - No restrictions, can be accessed by 3rd party control systems via Q-SYS Remote Control Protocol (QRC), or script objects or plugin objects.

Tip: Use Script Programmer Mode to quickly view the Script Access setting directly on the component in the design schematic without the need to disconnect from the Q-SYS Core processor.

Analog

Peak Input Level (dBFS)

Meters for each channel indicating the peak analog input level. The measurement is taken after the A/D converter, but before the Digital Gain. Use this meter in conjunction with the Max Input Level to obtain an input signal as close to 0 dBFS as possible without actually clipping.

Clip

Red LED indicating if the signal is being clipped.

Clip Hold

Holds the clip indication until manually cleared.

Phantom Power

Toggle turning on and off phantom power (+15VDC) to the microphone. Not available for the Line Inputs.

Preamp Sensitivity (dBu)

The maximum analog level, coming into the Analog Input, that can be converted without clipping. This level is typically set slightly higher than the source's output level, so that the Peak Input Level reads about 0 dBFS without actually clipping.

You can select the field and enter the value you want, or click and drag the number to the value.

Varies inversely with the Preamp Gain.

Preamp Gain knob (Mic Only) (dB)

The amount of Gain applied to the incoming analog signal level. Varies inversely with the Preamp Sensitivity.

Preamp Gain Buttons (Line Only)

The amount of Gain applied to the incoming analog signal level.

Left and Right toggle buttons toggle the Preamp Gain between 0dB when Off, and 12dB when On. this results in a change in Preamp Sensitivity.

Toggle Button	Preamp Gain	Preamp Sensitivity
Off	0dB	15dBu
On	12dB	3dBu

The values of 0dB and 12dB can be seen by connecting a Custom Controls "Text Display" to the Preamp Gain control pin output.

Digital

Invert

Toggle button to invert the digital output of Analog Input.

Mute

Toggle button to mute and unmute the output signal.

Gain (dB)

Controls the Gain of the digital output signal. Range is between -100 and 20 dB.

Status

Status LED

This LED changes color to indicate the current status of the Core. See Status for the meanings of the various colors.

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

• OK: The device is functioning normally.
• Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
• Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
• Missing: The device cannot be discovered.
• Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
• Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
• Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.