Status (I/O USB Bridge)

The I/O USB Bridge is a Q-SYS peripheral that converts Camera and Audio IP streams to USB. In the peripheral Properties, enable the USB Video Bridge and USB Audio Bridge to expose components for this capability.

Note: Audio Bridges allow you to use the volume controls on a Mac that is running 10.12.6 or higher and has the IO USB Audio Bridge selected.

Tip: For additional properties not listed, refer to the Properties Panel help topic for more information.

I/O USB Bridge

External USB Audio

When enabled, you can connect an external audio device to the USB input and route audio to and from that device. See External USB Audio Device In and Out.

Verbose

When set to Yes, the Control Panel displays Audio Stream Input and Output Statistics along with a Reset button to reset the statistics to zero.

Note: This field displays only when you have the I/O USB Status component in the design and selected. All other Properties are the same whether you have the USB Video Bridge or the I/O USB Bridge Status component selected.

Control

Function

Default / Range

ID

When the ID/Identify button, in the Q-SYS Designer Status component, or the Configurator's Network Configuration for the hardware, or on the physical hardware is pressed, the ID buttons in the Configurator and Status component flash, and the LCD on the physical Hardware flashes to indicate the association between the three.

The indicators will flash for 5 minutes unless you stop them by pressing any one of the buttons.

Off / On

Status LED

This LED changes color to indicate the current status of the Core. See Status for the meanings of the various colors.

N / A

Status

Displays color-coded messages indicating the current status of the active Core.

OK – Green – (0) – Audio and / or Video is good, hardware is good.

Compromised – Orange – (1) – Audio and / or Video is good but a redundancy mechanism is active (one LAN down but the other is still up) or a non-fatal hardware problem exists (fans too slow, temperature higher than expected, etc.)

Fault – Red – (2) – Audio and / or Video is not passing, or hardware is malfunctioning or mis-configured (amplifier power off, audio streams broken, wrong type of I/O Card installed, loudspeaker short circuit, etc.)

Missing – Red – (3) – A piece of hardware, defined in the design, has not been discovered. Audio and / or Video is not passing through that piece of hardware.

Initializing – Blue – (5) – In the process of firmware, configuration update, and design start. Audio and Video are obviously bad.

Not Present – Gray – A virtual component in the design, that is designated as Dynamically Paired, and Not Required ,has no hardware assigned to it.

N / A

Clock Offset

Indicates how much of an offset exists between this Core and the Master Clock. If this Core is the Master Clock, the offset is zero.

No default

Microseconds

Grandmaster

The clock master of the network.

N / A

Parent Port

The device and interface name that this device is syncing to when it's not the clock master. Usually it is the same as the Grandmaster name.

N / A

You must have USB Audio Bridge, in Properties, set to anything except Disabled to see the following.

Control

Function

Default / Range

Input / Output OK LED

(LAN A / LAN B)

You must have "Is Network Redundant" set to Yes in the Properties to see LAN B.

This LED changes color to indicate the current status of the I/O USB Bridge. See Status for the meanings of the various colors.

N / A

Suppress button

If the "Is Network Redundant" property is set to 'Yes', but the redundant network is not connected, an error is displayed. This button suppresses the error caused by LAN B not being connected.

 Off / On

Input / Output Details

The following details are available:

connected=1 (=1 connected / =0 not connected)

dscp=34 (Differentiated services code point) You can change this number in the Design Properties dialog (Menu > File > Design Properties).

accept_count= (number of packets accepted)

N / A

The following information is available only when the USB Audio Bridge, in the Properties, is set to anything except Disabled, and one or more of the USB Audio components are in the schematic.

Control

Function

Default / Range

Connection

Green LED indicating that the USB Out component is connected to a computer.

Off / On

USB Speed

Speed of the USB Connection. For example: High (2.0)

 N / A

Active

Green LED indicating that signal is streaming.

Off / On

More button

Click to show or hide the details listed below. (Samples, SRC+, SRC-)

N / A

Samples

Total number of samples since the audio started, or since the count has been reset.

N / A

SRC+

The number of samples added in order to match the USB clock with the Q-SYS PTP clock

N / A

SRC-

The number of samples removed in order to match the USB clock with the Q-SYS PTP clock

N / A

Reset

Resets the Sample count for the associated audio device.

N / A

The following information is available only when the USB Video Bridge, in the Properties, is set to Enabled, and the USB Video Bridge component is in the schematic. This applies to both the I/O USB Bridge and the Core 110f.

Input

Input LED

Indicates whether or not there is active input to the Q-SYS video input device.

Input Connection

The network name of the Q-SYS video input device.

Bitrate (Kb/s)

The current input video bitrate, in kilobits per second.

Frames per Sec

Number of frames per second being sent by the video device.

Frame Count

Total number of frames sent.

Packet Count

Total number of packets since the last reset.

Packets Lost

Number of packets lost since the last reset.

Packet Loss%

The percentage of packets lost based on Packets Lost and Packet Count.

Test Button

Test the network setup for the Q-SYS video streaming implementation without having a PC or any USB connection. This tests QoS and IGMP on multicast.

USB

USB Active LED

Video Bridge USB Active: Indicates if the USB is active or not.

USB Bridge Name

The network name of the Q-SYS video bridging device.

Video Format

Displays the format of the video present on the USB – for example, "1920x1080p30".

Encoding

Displays the type of encoding used for the USB video stream - for example, "MJPEG".

USB Speed

Displays the detected USB speed capability of the connection – for example, "High Speed (2.0)".

Bitrate (Mb/s)

USB bitrate, in megabits per second.

Frames per Sec

USB frames per second

SRC-

The number of samples removed in order to match the USB clock with the Q-SYS PTP clock

SRC+

The number of samples added in order to match the USB clock with the Q-SYS PTP clock

Reset

Reset Button

Clears the readings, and restarts monitoring.

Pin Name

Value

String

Position

Pins Available

Clock Grandmaster Name

Text box indicating the network name of the Network Clock Grandmaster

Output

Clock Offset From Master

–

0 ms to n ms

–

Output

Clock Parent Port Name

Text box indicating the network name of the Parent port, usually the same as the Clock Grandmaster with the LAN appended.

Output

I/O USB Bridge Status

Text field displaying the current status of the I/O USB Bridge

Output

Identify

0

1

false

true

0

1

Input / Output

Pin Name

Value

String

Position

Pins Available

LAN A (LAN B) Input Stream Details

Read-only text field listing details about the Input audio streams.

Output

LAN A (LAN B) Input Stream OK

0

1

false

true

0.00

1.00

Output

LAN A (LAN B) Output Stream Details

Read-only text field listing details about the Output audio streams.

Output

LAN A (LAN B) Output Stream OK

0

1

false

true

0.00

1.00

Output

LAN B Suppress button

0

1

false

true

0.00

1.00

Output

The following control pins are available on the Speakerphone In and Out, Sound Card In and Out components.

Pin Name

Value

String

Position

Pins Available

Active

0

1

Off

On

0

1

Output

Reset Counters

Trigger button

 Input / Output

SRC-

0 and up

0 and up

0.00 to 1.00

 Output

SRC+

0 and up

0 and up

0.00 to 1.00

Output

Total Samples

0 and up

0 and up

0.00 to 1.00

Output

USB Connected

0

1

Off

On

0

1

Output

USB Speed

Text Field

Output

The following control pins are available when the Status component or the USB Video Bridge component is selected.

Pin Name

Value

String

Position

Pins Available

IP Streams 1 and 2

Bitrate

0.0000 and up

0.0000 and up

0.00 to 1.00

Output

FPS

0 to 30

0 to 30

0.00 to 1.00

Output

Frame Count

0 and up

0 and up

0.00 to 1.00

Output

Packet Count

0 and up

0 and up

0.00 to 1.00

Output

Packet Loss Percentage

0.00 to 100

0.00% to 100%

0.00 to 1.00

Output

Packets Lost

0 and up

0 and up

0.00 to 1.00

Output

Test Stream 1, 2

0

1

false

true

0

1.00

Input / Output

USB

Active

0

1

false

true

0

1.00

Output

Bitrate

0.0000 and up

0 and up

0.00 to 1.00

Output

Bridge Name

(text)

Output

Encoding

(text)

Output

FPS

0 to 30

 0 to 30 0.00 to 1.00

Output

SRC-

 0 and up

0 and up

 0.00 to 1.00

Output

SRC+

 0 and up

0 and up

 0.00 to 1.00

Output

USB Speed

(text)

Output

Video Format

(text)

Output

Input Active

0

1

false

true

0

1.00

Output

Input Connection

(text)

Output

Reset

0

1

0 or false

1 or true

0.00

1.00

Input / Output