Control (NL-SB42, NM-T1)

Endpoints

When the Enable Call Sync property is enabled, connect this input pin to the Call Sync output pin of a supported call system. For a list of supported call systems, see the Call Sync [BETA] topic.

In this simple example, the Control component for an NL-SB42 soundbar is configured to receive call status from a HID Conferencing component using Call Sync pins. The Control component's Enable Call Sync property is set to 'Yes'.

Name

The Name may contain ASCII letters 'a' through 'z' (case-insensitive), the digits '0' through '9', and the hyphen. Names cannot begin or end with a hyphen. No other symbols, punctuation characters, or blank spaces are permitted.

Location

User-defined name that groups the component with other components in the same physical location, or in the same organizational scheme.

Is Required

When enabled, and the device is not found on the network, the device is reported as 'Missing', which is an error condition. This is the default behavior. When disabled, and the device is not found on the network, the device is reported as 'Not Present', which is not an error condition.

Dynamically Paired

Indicates that this virtual component can be paired with the same type of hardware without changing the network ID of the hardware or the name of this component. Refer to the Q-SYS Core Manager Dynamic Pairing topic for more information. The default is 'No'.

Enable Call Sync

Select whether to expose a Call Sync input pin, which can receive call states from either a Q-SYS calling system directly or the Call Sync [BETA] component. The default is 'No'.

Note: Button Configuration and Proximity Sensor controls are related to the Q-SYS NM-T1 Tabletop Network Microphone. This device will be available in a future release.

Button Configuration

Mute Mode

Alters the microphone Mute button behavior.

• Toggle : (Default) When a Mute button is pressed, it toggles between mute and unmute states. Only toggle is supported when using Call Sync. PTT (Push to Talk) and PTM (Push To Mute) are supported when using the NM-T1 without Call Sync.

Mute Control

This control determines whether audio is muted within the Mic In (NM-T1) component.

• Local: (Default) When set to local, any mute button press on the NM-T1 device or virtual mute buttons will cause the audio to be muted within the NM-T1 Mic In component.

• Remote: When set to Remote and mute buttons are pressed, audio is not muted within the NM-T1 Mic In component. In this mode, the mute state output can be used to control muting in the Q-SYS design.

Mute Buttons

This control enables or disables the four Mute buttons on the NM-T1 device. When set to Disabled, the Mute button backlights on the control ring turn off. The default is Enabled.

Call Button

This control enables or disables the Call button on the NM-T1 device. When set to Disabled, the Call button backlight on the control ring turns off. The default is Disabled.

User Button

This control enables or disables the User button on the NM-T1 device. When set to Disabled, the User button backlight on the control ring turns off. The default is Disabled.

Proximity Sensor

Sensor

This control enables or disables the proximity sensor on the NM-T1 device. The default is Disabled

Fuel Gauge

This control enables or disables the fuel gauge pattern when the proximity sensor is activated on the NM-T1 device. The default is Enabled.

Link to Mute

When enabled, a proximity sensor event will toggle the mute state of the NM-T1 microphone. The default is Enabled.

LED Configuration

Use this section to configure the Unmute, Mute, Ringing, and Idle states of supported Q-SYS collaboration Endpoints with integrated LEDs (see Control (NL-SB42, NM-T1)) and how those states are indicated to the user on the LED light bar or ring.

Tip: When connected to a running system, any change to the color, pattern, or speed controls will preview the combination for 5 seconds regardless of the current state of the Endpoint.

Color

For each state, select what color appears in the light bar or light ring:

• <Color Name>: Select from 16 color names in the list.

• Off: The LED will turn off for this state.

• Custom: For greater color capability, wire a Color Picker component to the Color input control pin for each state. See Control (NL-SB42, NM-T1).

Pattern

For each state, select a pattern for LED colors to appear: Breathing, Chasing, Chasing w/Tails, Flashing, or Solid (default).

Speed

For each state, select the speed of the selected pattern animation: Slow, Standard, Fast, or None.

User Button Color

Similar to the Color control for call states, you can also configure the color for the NM-T1 User button.

LED Brightness

Select the brightness level of the light bar or ring, from 1 (dimmest) to 10 (brightest). The default is 5. On the NM-T1, this also adjusts the brightness of the Mute, Call, and User button backlights.

Pin Name	Value	String	Position	Pins Available
Idle Color	-	Aquamarine Blue Blue Violet Coral Custom Cyan Green Green Yellow Lime Magenta Off Orange Orchid Pink Red Sky Blue White Yellow	-	Input/Output
Idle Pattern	-	Solid Flashing Breathing Chasing Chasing with Tails	-	Input/Output
Idle RGB	-	#nnnnnn	-	Input/Output
Idle Speed	-	Slow Standard Fast None	-	Input/Output
LED Brightness	1 to 10	1 to 10	0.00 to 1.00	Input/Output
LED Color	-	#nnnnnn	-	Input/Output
LED Fuel State	0 1	false true	0 1	Input/Output
LED Idle State	0 1	false true	0 1	Input/Output
LED Mute State	0 1	false true	0 1	Input/Output
LED Ringing State	0 1	false true	0 1	Input/Output
Mute Color	-	Aquamarine Blue Blue Violet Coral Custom Cyan Green Green Yellow Lime Magenta Off Orange Orchid Pink Red Sky Blue White Yellow	-	Input/Output
Mute Pattern	-	Solid Flashing Breathing Chasing Chasing with Tails	-	Input/Output
Mute RGB	-	#nnnnnn	-	Input/Output
Mute Speed	-	Slow Standard Fast None	-	Input/Output
Ringing Color	-	Aquamarine Blue Blue Violet Coral Custom Cyan Follow Mute Green Green Yellow Lime Magenta Off Orange Orchid Pink Red Sky Blue White Yellow	-	Input/Output
Ringing Pattern	-	Solid Flashing Breathing Chasing Chasing with Tails	-	Input/Output
Ringing RGB	-	#nnnnnn	-	Input/Output
Ringing Speed	-	Slow Standard Fast None	-	Input/Output
Unmute Color	-	Aquamarine Blue Blue Violet Coral Custom Cyan Green Green Yellow Lime Magenta Off Orange Orchid Pink Red Sky Blue White Yellow	-	Input/Output
Unmute Pattern	-	Solid Flashing Breathing Chasing Chasing with Tails	-	Input/Output
Unmute RGB	-	#nnnnnn	-	Input/Output
Unmute Speed	-	Slow Standard Fast None	-	Input/Output