NL-SB42

The Q-SYS NL-SB42 is a network PoE soundbar that delivers clear speech and music reproduction natively to Q-SYS. It features a two-way design that provides wide off-axis response, and is optimized to better handle program content (in addition to voice content). The Q-SYS NL-SB42 supports vertical or horizontal mounting and can be integrated into your space with a single Ethernet cable to reduce overall hardware footprint and lower system cost. As a native Q-SYS Product, you can take advantage of the drag-and-drop integration and simple control capabilities offered by Q-SYS.

Note: This topic provides an overview of the NL-SB42. For specifications and installation documentation, see the NL-SB42 product page on the QSC website.

  • 3.5-inch woofer + 0.75-inch tweeter

  • Two-way design provides wider off-axis response and is optimized to better handle program content (in addition to voice content)

  • Power over Ethernet enables power, data and control over a single cable

  • Programmable light bar (within Q-SYS Designer Software)

  • Consistent tonal characteristics across the entire NL Series family let you mix and match enclosure types

  • Ideal for speech and music applications

  • Simple drag-and-drop integration and comprehensive management via Q-SYS Designer Software and Q-SYS Reflect Enterprise Manager

  • Q-SYS automatically delivers custom loudspeaker voicings (Intrinsic Correction™) to simplify the tuning process

  • Q-SYS Call Sync compatible, letting you sync status across supported Q-SYS products without complicated programming

  • Includes quick-install wall bracket, with 3 cm of fine adjustment (supports vertical and horizontal mounting)

  • Optional feet for bookshelf mounting

These Inventory components are available for the NL-SB42:

Front

  1. LED Light Bar: Indicates the status of the NL-SB42:

    • Flashing yellow = Identify

    • Slow flashing blue = Initializing

    • Slow flashing red = Fault

Rear

  1. Q-LAN/PoE Port: For Q-LAN connection. The NL-SB42 is a PoE Enabled Device (PoE+ Type 2 Class 4 capable). Use a suitable PoE network switch or supply connected to this port.

  2. ID Button: Press to identify this product in Q-SYS Designer Software and Q-SYS Configurator.

  3. Reset Button: Use the Reset button to restore default network settings and recover factory default settings. Before attempting a reset, refer to the Device Reset section.

Product specifications and dimension drawings for the NL-SB42 can be found on the NL-SB42 product page.

You can perform either a short reset or long reset:

  • Use a Short Reset to restore connectivity to a device in the event that unintended network settings were specified in Q-SYS Peripheral Manager or the device is otherwise unreachable. A short reset will restore device IP settings back to Auto mode (DHCP) and delete all Static Routes. The configured hostname is retained.
  • Use a Long Reset to restore the device to factory condition. This is useful for deeper troubleshooting, or when preparing the device for decommissioning or transfer.

    CAUTION: A Long Reset clears all network settings (including hostname), disables 802.1x, deletes user-installed device certificates, deletes all logs, and clears the device password.

Performing a Short Reset

  1. Press and hold the Reset Button until the Status LED (NL, NM Series) or Power LED (QIO Series) begins flashing blue slowly – approximately 10 seconds.
  2. Release the button before 20 seconds elapse.
  3. The device performs its prescribed Short Reset and reboots.

Note: To cancel the Short Reset, release the button before 10 seconds has elapsed.

Performing a Long Reset

  1. Press and hold the Reset Button until the Status LED (NL, NM Series) or Power LED (QIO Series) begins flashing blue rapidly – approximately 20 seconds.
  2. Release the button when the LED begins flashing rapidly.
  3. Within 30 seconds, press the Reset Button again to confirm the reset.
  4. The device performs its prescribed Long Reset and reboots.

Note: To cancel the Long Reset, do not press the Reset Button again during the 30 second confirmation period.