QIO-FLEX4A
The QIO-FLEX4A is an all-in-one network I/O peripheral for presentation, discussion, and connected collaboration spaces.
Note: This topic provides an overview of the QIO-FLEX4A. For specifications and installation documentation, see the FLEX4A product page.
The Q-SYS QIO Series network audio I/O expanders include these features:
- Native audio I/O expanders for Q-SYS
- QIO-ML4i: Four (4) mic/line inputs
- QIO-L4o: Four (4) line outputs
- QIO-ML2x2: Two (2) mic/line inputs and two (2) line outputs
- QIO-AES8x8: Four (4) AES3 Inputs and four (4) AES3 Outputs
- QIO-TEL2: Two (2) PSTN (POTS) interfaces
- QIO-FLEX4A: Four (4) Flex I/O Audio Channels, 4x8 GPIO Ports, two (2) Amplifier Outputs, one (1) RS232.
- Professional mic/line level inputs with +48 VDC phantom power and/or line outputs
- Microphone detection on inputs enables monitoring, usage statistics, and failure notifications
- Power-over-Ethernet capable
- Daisy-chain up to four QIO network I/O expanders on a single network run (with local daisy-chained DC power)
- Simple drag-and-drop integration and comprehensive management via Q-SYS Designer Software and Q-SYS Reflect
- Surface- or rack-mountable
- Includes surface mounting hardware
- QIO-RMK rack mounting kit sold separately
- QIO-PSU DC power supply sold separately
These Inventory components are available for the QIO-TEL2:
Front Panel
-
Power LED – Illuminates blue when the Q-SYS QIO-FLEX4A is powered on.
-
ID LED – LED blinks green when placed into ID Mode via ID Button or Q-SYS Configurator.
-
ID Button – Locates the QIO-FLEX4A in Q-SYS Designer Software and Q-SYS Configurator.
Rear Panel
-
External Power Input 24V DC 3.7 A – Auxiliary power, 24V DC, 3.7 A, 2-pin Euro connector.
-
Daisy-Chain Power Output 24V DC 1.9 A – Auxiliary power, 24V DC, 1.9 A 2-pin Euro connector.
-
LAN [PoE] – RJ-45 connector, 802.3at Type 2 power, Q-LAN.
-
LAN [THRU] – RJ-45 connector, Ethernet daisy-chaining.
-
Device Reset – Use a paperclip or similar tool to restore default network settings and recover factory default settings. Before attempting a reset, refer to the Q-SYS Help for details.
-
RS232 – COM: TX pin (output, transmit data), RX pin (input, receive data), Ground pin (signal ground), WT pin (5.5V DC 70 mA max).
-
AMP Out – 2 channels, 5W per channel (PoE+) or 9W per channel (Aux power).
-
Signal Ground – For use with General Purpose Inputs and Outputs (GPIO). Uses connector pin 14 (not numbered).
-
GPIO Outputs – 8 outputs, open collector (24V, 0.2A sink maximum) with pull up to +3.3V (pins labeled 1–8 equal pins 1–8 in the Q-SYS Designer GPIO Output component).
-
GPIO Inputs – 4 inputs, 0-24V analog input, digital input, or contact closure (pins labeled 1–4 equal pins 1–4 in the Q-SYS Designer GPIO Input component). Configurable pull-up to +12V.
-
12V DC .1A Out – For use with GPIO. Uses connector pin 1 (not numbered).
-
FLEX Channels – 4 user-configurable audio channels (mic/line input with optional phantom power, or line output), balanced or unbalanced.
Product specifications and dimension drawings can be found on the QIO-FLEX4A product page.
You can perform either a short reset or long reset:
- Use a Short Reset to restore connectivity to a device in the event that unintended network settings were specified in Q-SYS Peripheral Manager or the device is otherwise unreachable. A short reset will restore device IP settings back to Auto mode (DHCP) and delete all Static Routes. The configured hostname is retained.
- Use a Long Reset to restore the device to factory condition. This is useful for deeper troubleshooting, or when preparing the device for decommissioning or transfer.
CAUTION: A Long Reset clears all network settings (including hostname), disables 802.1x, deletes user-installed device certificates, deletes all logs, and clears the device password.
Performing a Short Reset
- Press and hold the Reset Button until the Status LED (NL, NM Series) or Power LED (QIO Series) begins flashing blue slowly – approximately 10 seconds.
- Release the button before 20 seconds elapse.
- The device performs its prescribed Short Reset and reboots.
Note: To cancel the Short Reset, release the button before 10 seconds has elapsed.
Performing a Long Reset
- Press and hold the Reset Button until the Status LED (NL, NM Series) or Power LED (QIO Series) begins flashing blue rapidly – approximately 20 seconds.
- Release the button when the LED begins flashing rapidly.
- Within 30 seconds, press the Reset Button again to confirm the reset.
- The device performs its prescribed Long Reset and reboots.
Note: To cancel the Long Reset, do not press the Reset Button again during the 30 second confirmation period.