Acoustic Echo Canceler

The Q‐SYS multi‐channel Acoustic Echo Canceler (AEC) component is used in conference rooms (Near-End) and other installations where people call in from remote locations. The remote caller's (Far-End caller's) voice is broadcast over loudspeakers in the conference room. The sound is picked up by microphones in the conference room and echoed back to the Far-End caller. The purpose of the AEC is to eliminate these echoes while at the same time allowing the Far-End caller to hear clearly, what people in the room are saying.

Each microphone in the conference room is plugged into one channel of the Q-SYS AEC component. Each channel also receives the loudspeaker signal that carries the remote talker's voice. This is called the AEC reference signal. To remove the echoes, the AEC subtracts a filtered version of the reference signal from the microphone signal.

Tip: To learn more about AEC, see the Acoustic Echo Cancellation (AEC) Application topic. For AEC best practices, refer to the QSC Quantum Level 1 Training Online.

Max AEC Channels per Core by Tail Length

Note: Q-SYS Scaling Licenses expand the capabilities of some Q-SYS Core processor models. Refer to the Licensing topic for more information.

Tail Length > 100 ms 200 ms 300 ms 400 ms

NV-32-H (Core Capable)

12

8

6

4

Core Nano

12

8

6

4

Core 8 Flex

12

8

6

4

Core 110f

24

16

12

8

Core 510i

96

64

48

32

Core 610

96

64

48

32

Core 5200

240

160

120

80

Core 6000 CXR

120

80

60

40
Discontinued  

Core 1100

96

72

48

24

Core 3100

192

144

96

48

AEC Signal Delays

Most modern AEC systems, including Q-SYS AEC, process the signal in many narrow frequency bands. This introduces a delay in the signal:

AEC Delay Type > Input-to-conference-output Input-to-reinforcement-output

Core 8 Flex

Core Nano

NV-32-H (Core Capable)

Core 110f

32 milliseconds

21.4 milliseconds

All other Cores

26.7 milliseconds

10.7 milliseconds

Input Pins

Microphone

Connect to the Near-End conference room microphones.

Reference

This pin receives a single incoming audio signal from a Far-End audio source, such as a Speakerphone In component (USB Audio Bridge), VoIP In (Softphone), or POTS In component. The Reference is then used for AEC processing.

Outputs

Conference

Output to the Far-End phone. Connect this pin to audio processing components (equalizers, mixers, etc.) and finally to an audio output, such as Speakerphone Out, VoIP Out, or POTS Out, depending on the conferencing solution within the design.

Reinforcement

Optional. If enabled in Properties, this pin outputs to the Near-End conference room loudspeakers. See Properties > Reinforcement Output for more information.

In this example, there are 8 microphones routed through an Acoustic Echo Canceler to eliminate echos for the remote caller's (Far-End caller's).

Acoustic Echo Canceler Properties

Tail Length ms

Tail length is the maximum room impulse response that the adaptive filter can model.

Typically, you would use 200 ms, but for exceptionally reverberant rooms, you may want to use 400 ms.

When the Tail Length is set to 400 ms, the channel count is doubled when calculating AEC Processing in Check Design (Shift+F6), which effectively cuts the number of available channels in half.

Channel Count

Selects the number of input channels available for the AEC. Each Core has a set limit of channels you can use in a design. Note that an AEC channel with a Tail Length of 200ms requires double the processing of one with a Tail Length of 100ms. Likewise, an AEC channel with a Tale Length of 400ms requires four times the processing of one with a Tail Length of 100ms.

Shared Reference

Select Yes to have one input Reference signal shared by all channels.

Reinforcement Output

Select Yes to make a Reinforcement output pin available for each channel. No is the default. When enabled, connect the Reinforcement pin to the Near-End conference room loudspeakers.

Sound Reinforcement (SR), also known as "voice-lift", is typically enabled in larger conference rooms, where it is desirable to have the Near End talker’s voice amplified over the room's loudspeakers. When the Reinforcement Output property is enabled and the Reinforcement pin is connected to the Near-End conference room loudspeakers, Q-SYS takes the output of the AEC after the adaptive filter subtraction operation but before the non-linear processor (NLP). The SR output is then mixed with the Far End reference and sent to the loudspeaker. Enabling and wiring the Reinforcement pin is usually more desirable than other sound reinforcement applications, which can suffer from acoustic feedback (howling) problems in the Near End room due to the direct path from loudspeaker to microphone.

Tip: Additional system and component latency combined with the Reinforcement Output latency can increase the total delay from microphone to loudspeaker. This can be excessive in some live sound situations. In these cases, it may be preferable to use a direct connection from microphone to loudspeaker rather than the Reinforcement Output pin.

Max Noise Reduction

Select the maximum level of noise reduction allowed with the Noise Reduction (NR) control.

Note: In most cases, this should be left at the default of 10dB to avoid distorting sound quality.

Graphic Properties

Label

Use the Label property to change the name of the component in the schematic. The Label property defaults to the component name. To learn more about renaming schematic elements, see Organizing Your Design.

Position

The coordinates reference a specific place in the schematic - for example,"100,100" (horizontal, vertical). 0,0 is the upper left corner of the schematic.

Fill

Sets the fill color of the component in the schematic.

Script Access Properties

Code Name

Displays the currently assign name for control access. You can use the auto-assigned name or customize it. Q-SYS will automatically check all Code Names in the design to ensure name is unique.

Script Access

Defines whether the component will be accessible by script and/or externally, or not at all. Choices include All, External, None (default), and Script.

Tip: Use Script Programmer Mode to quickly view the Script Access setting directly on the component in the design schematic without the need to disconnect from the Q-SYS Core processor.

Echo Return Loss Enhancement (ERLE)

This meter indicates how much, in dB, the Far-End echo arriving at the Near-End microphone is attenuated by the AEC adaptive filter once the filter has converged.

The ERLE meter is used to indicate how effective the AEC is in terms of suppressing the acoustic echo. A reading below 10 dB during Far-End only talk may indicate that the room tail is longer than the AEC tail property. Readings above 20 dB during Far-End only talk indicate that the AEC is working properly.

Bypass

Bypasses the AEC function, including its latency, when activated. The default is Off.

Reference-to-Microphone Level Ratio (RMLR)

This meter indicates how much, in dB, the Far-End reference signal level exceeds the Near-End microphone signal level.

The RMLR meter is used to adjust the reference signal level during Far-End only talk. In general, the Far-End reference signal level should approximately equal the Near-End microphone signal level, as indicated by a ratio of 0dB. The ratio can be adjusted using the Reference Gain knob.

Target 0dB

Adjust the Reference Gain until the RMLR is at the target of 0dB.

Reference Gain

This knob adjusts, in dB, the Far-End reference signal level. The default is 0.

In general, the Far-End reference signal level should approximately equal the Near-End microphone signal level, as indicated by 0dB on the Reference-to-Microphone Level Ratio meter.

Hold If Mic Level Below

Sets the threshold, in dB between -100 and 0, below which AEC adaptation stops. The default is -100dB. In most cases, the microphone signal will be nonexistent when the mic's mute feature is activated, so this level should be left at the default of -100 dB. However, if your microphone only strongly attenuates the signal when muted, this weak signal can cause issues with AEC adaptation. In this case, try adjusting the Hold level to just above the level when the mic is muted.

Tip: For example, if your microphone signal is -80 dB when the mute feature is activated, try adjusting the Hold level to -60 dB.

Hold If Ref Level Below

Sets the threshold, in dB between -100 and 0, below which the AEC adaptation stops. The default is -100dB. In most cases, the Far-End reference signal is clean and of sufficiently high level, so this level should be left at the default. However, if the Far-End reference signal has elevated background noise, this noise can cause issues with AEC adaptation. In this case, try adjusting the Hold level to just above the Far-End background noise level.

Residual Echo Suppression (RES) %

Residual Echo Suppression applies additional suppression to any residual echo that was not removed by the adaptive filter and echo reduction functions of the AEC component.

This control determines how much any residual echo is suppressed. The more you turn it up, the more aggressively the residual echo is suppressed at the expense of distorting the Near-End microphone signal.

RES Enable

Enables and disables Residual Echo Suppression functionality of the AEC.

Noise Reduction (NR) dB

Noise Reduction reduces the level of relatively steady state noises like fans, lawn mowers, wind, and mains electrical hum. The goal is to reduce these noises without affecting the desired speech.

This control determines how much, in dB, these steady-state noises are reduced. The more you turn it up, the more aggressively the noise is removed at the expense of distorting the Near-End microphone signal.

NR Enable

Enables and disables the noise reduction functionality of the AEC.

Pin Name

Value

String

Position

Pins Available
For Each Channel

AEC Bypass

0

1

no

bypassed

0

1

Input / Output

Echo Return Loss Enhancement

 0 to 20 0 dB to 20 dB

0

1

Output

Hold If Microphone Level Below

-100 to 0

-100dB to 0dB

0.000 to 1.00

Input / Output

Hold if Reference Level Below

 -100 to 0

-100 to

0dB

0.000 to

1.0

 Input / Output

Reference Gain

-40 to 0

-40dB to 0dB

0.00 to 1.00

 Input / Output

Reference-to-Microphone Level Ratio

-10 to 10

-10 dB to 10 dB

0

1

 Output
For Component

Noise Reduction

0.0 to 30.0

0 dB to 30.0 dB

0.000 to 1.00

Input / Output

Noise Reduction Enable

0

1

disabled

enabled

0

1

Input / Output

Residual Echo Suppression

0 to 100

0% to 100%

0.000 to 1.00

Input / Output

Residual Echo Suppression Enable

1

0

enabled

disabled

1

0

Input / Output