HDMI I/O (NV-32-H)

In this mode, the HDMI I/O component represents a local 3 x 2 HDMI video switcher with the ability to receive and locally display Mediacast streams. Q-SYS Shift Networked AV Streaming is not supported.

Mediacast Streaming

• Select a single incoming Mediacast stream from an NC Series or PTZ Series camera to display locally on HDMI AV Output 1. Display on HDMI AV Output 2 is not supported.
• Camera Mediacast streams are always in 16:9 aspect ratio and scaled to "stretch to fit" mode for displays that are not 16:9.

Local HDMI Switching

• Onboard HDMI switching is 3 x 1 @ 4K60 or 3 x 2 @ 1080p.

For NV-32-H (Core Capable) devices in Peripheral Mode or NV-32-H Network Video Endpoints, the HDMI I/O component represents a single NV-32-H device configured as an Encoder or Decoder for sending or receiving AV signals over the network.

Q-SYS Shift Networked AV Streaming

• An Encoder takes source HDMI AV signals and places them on the network in streams. Encoders can process a single stream up to 4K60 or three simultaneous streams up to 1080p60 each.
• A Decoder processes incoming network HDMI signals and sends them to a display. Decoders can process a single stream up to 4K60 or two simultaneous streams up to 1080p60 each.

Mediacast Streaming

• Select a single incoming Mediacast stream from an NC Series or PTZ Series camera to display on the Encoder or Decoder's local HDMI AV Output 1. Output 2 is not supported with Mediacast streams.
• Mediacast streaming is local to the NV-32-H device. You cannot stream Mediacast between Encoder AV Outputs and Decoder AV Inputs in your design.
• Camera Mediacast streams are always in 16:9 aspect ratio and scaled to "stretch to fit" mode for displays that are not 16:9.

Local HDMI Switching

• For Encoders, use HDMI Output 1 as a “courtesy monitor”, displaying any of the three locally connected HDMI sources at resolutions up to 4K60.
• For Decoders, toggle between network streams or locally connected HDMI sources (single 4K60 or dual 1080p60 sources).

Input Pins

HDMI AV Input 1, 2, 3

Each pin represents one of the three HDMI inputs on the NV-32-H. Connect this pin to a Generic AV Source component HDMI AV Output pin.

Output Pins

HDMI AV Output 1, 2

This pin outputs a selectable signal from any of the HDMI I/O inputs, including the AV inputs and local HDMI inputs. Connect this pin to a Generic HDMI Display HDMI AV Input pin. By default, a single HDMI AV output pin is exposed. However, if you configure the HDMI Output Mode component property to "HDMI 1 + HDMI 2", a second output pin is exposed.

Note: Each HDMI output supplies up to 120mA on the +5v signal line.

HDMI 1, 2 Channel 1, 2

If enabled in the component Properties (HDMI Output Mode is set to "HDMI 1 + HDMI 2"), select the number of audio pins to expose – from 0 to 8 – for routing to other Q-SYS audio components, such as a network amplifier. This audio corresponds to the HDMI Output 1 or 2 source you select in the HDMI I/O control panel.

Tip: These pins automatically send audio for whatever HDMI video source is selected for display. No additional programming is required to align audio and video signals.

Tip: For guidance on surround sound channel assignment, see this article in the Q-SYS Knowledge Base.

Input Pins

HDMI AV Input 1, 2, 3

Each pin represents one of the three HDMI inputs on the NV-32-H. Connect this pin to a Generic AV Source component HDMI AV Output pin.

Output Pins

AV Output 1, 2, 3

The AV Output pins send combined HDMI video and audio signals over the Q-LAN network. Each of the three outputs correspond to a respective HDMI AV Input pin – for example, AV Output 1 transmits the incoming HDMI signal from HDMI AV Input 1. Connect an AV Output pin to an AV Input pin on the HDMI I/O Decoder component.

HDMI AV Output 1

If enabled in the component Properties (HDMI Output Mode is set to "HDMI 1"), this pin outputs a selectable signal from one of the three HDMI inputs on the NV-32-H. Connect this pin to a Generic HDMI Display HDMI AV Input pin.

Note: Each HDMI output supplies up to 120mA on the +5v signal line.

HDMI 1 Channel 1, 2

If enabled in the component Properties (HDMI Output Mode is set to "HDMI 1"), select the number of audio pins to expose – from 0 to 8 – for routing to other Q-SYS audio components, such as a network amplifier. This audio corresponds to the HDMI Output 1 source you select in the Encoder control panel.

Tip: For guidance on surround sound channel assignment, see this article in the Q-SYS Knowledge Base.

Input Pins

AV Input 1, 2, 3

The AV Input pins receive the combined HDMI video and audio signals from the Q-LAN network. Connect an AV Input pin to an AV Output pin on the HDMI I/O Encoder component.

HDMI AV Input 1, 2, 3

Each pin represents one of the three HDMI inputs on the NV-32-H. Connect this pin to a Generic AV Source component HDMI AV Output pin.

Output Pins

HDMI AV Output 1, 2

This pin outputs a selectable signal from any of the HDMI I/O inputs, including the AV inputs and local HDMI inputs. Connect this pin to a Generic HDMI Display HDMI AV Input pin. By default, a single HDMI AV output pin is exposed. However, if you configure the HDMI Output Mode component property to "HDMI 1 + HDMI 2", a second output pin is exposed.

Note: Each HDMI output supplies up to 120mA on the +5v signal line.

HDMI 1, 2 Channel 1, 2

If enabled in the component Properties (HDMI Output Mode is set to "HDMI 1 + HDMI 2"), select the number of audio pins to expose – from 0 to 8 – for routing to other Q-SYS audio components, such as a network amplifier. This audio corresponds to the HDMI Output 1 or 2 source you select in the Decoder control panel.

Tip: These pins automatically send audio for whatever HDMI video source is selected for display. No additional programming is required to align audio and video signals.

Tip: For guidance on surround sound channel assignment, see this article in the Q-SYS Knowledge Base.

When the NV-32-H (Core Capable) is configured in Core Mode, the device serves not only as an integrated audio, video, and control processor (as with other Q-SYS Core processors) but also as a local HDMI switcher. In this example, the NV-32-H (Core Capable) accepts HDMI connections from three conference room user laptops and routes the HDMI signals to the conference room monitor.

This example shows a typical conference room configuration. Three HDMI source signals (for example, computer HDMI audio and video) can be encoded by one NV-32-H network endpoint mounted under a conference room table. The signals are transmitted over the Q-LAN network and decoded by another NV-32-H connected to a wall-mounted HDMI display. Whatever network AV source selected in the Decoder is sent to the display, with amplification of two channels of audio from the selected source.

This example is similar to Example 1, except that a "courtesy" monitor is connected to the HDMI 1 output on the NV-32-H Encoder. This allows a presenter to select one of the HDMI sources for viewing on a separate monitor. For example, this would be useful for a lecturer to view the presented source on a small lectern monitor without having to turn around to see the main display.

Note: Audio from an Encoder's local HDMI 1 output can also be routed to Q-SYS audio components for processing in the Q-SYS Core's DSP. To enable HDMI and audio output pins on an Encoder, set the HDMI Output Mode property to "HDMI 1" and set the number of HDMI 1 Audio Pins.

Tip: You can also route audio directly from an HDMI source by enabling Breakaway Audio for that source. For more information, and to see an example, see Generic AV Source.

This example adds the ability to connect up to three local HDMI sources to the NV-32-H Decoder, such as Blu-ray players, network streaming devices, and similar. Users can thus select from six AV sources (three network, three local) to display in the room, with amplification of the selected source.

In this example, the room contains two HDMI displays. Each can display a separate network AV source. Audio from both sources is routed to a Matrix Mixer and is then amplified.

Note: To enable HDMI Output 2 pins on a Decoder and route separate AV streams to dual displays, set the HDMI Output Mode property to "HDMI 1 + HDMI 2".

Tip: You can also route audio to a display by exposing audio input pins for that display. This can be useful, for example, for inserting audio from a Q-SYS PA system (pages) for output on a display's internal speakers or a connected speaker bar. For more information, and to see an example, see Generic HDMI Display.

In this example, the primary room's NV-32-H is sending unicast streams on its AV Output 1 and 2 pins. However, AV Output 3 is sending a stream to both the NV-32-H in the primary room and a secondary location, thus making this a multicast stream. In the secondary location, the stream is decoded and output to an HDMI display. This location has no amplifier and speakers, so the stream audio is heard via the display's internal speakers or connected speaker bar.

HDMI Output 1, 2 Source

Select which sources to output through the Decoder's HDMI AV Output pins. The section for HDMI Output 2 Source only appears when the HDMI Output Mode component property is set to "HDMI 1 + HDMI 2". You can select a source using either the drop-down menu, numeric input, or trigger buttons. The Active HDMI LED indicates what sources are active and selectable.

• Graphic 1, 2, 3: Toggle a graphic to display that you assign in Q-SYS Core Manager. Numeric input values are 1, 2, and 3.
• HDMI 1, 2, 3: These inputs correspond to the sources connected to the HDMI AV Input pins 1, 2, 3. Numeric input values are 4, 5, and 6.
• Mediacast In n: (HDMI Output 1 Source only) These inputs correspond to the Mediacast sources (cameras) connected to the Mediacast Input pins. The number of selectable sources equals what is specified for the Mediacast > Input Count property. Numeric input values begin at 7.
• Follow H1: (HDMI Output 2 Source only) If the HDMI Output Mode property is set to "HDMI 1 + HDMI 2", this control appears for the HDMI Output 2 Source. When enabled, HDMI Output 2 uses whatever source is selected for HDMI Output 1. When enabled, the maximum resolution is 1080p60 for both outputs.

Encoder Network Settings

IP Streaming

LED indicates whether the Encoder is actively transmitting AV audio and video data to a Decoder via SRTP on the Q-LAN network. This applies to both unicast or multicast streams.

SRTP Address

Displays the IP address that the Encoder is using to send AV network audio and video streams directly to Decoders:

• For unicast streams, this is the Encoder's IP address.
• For multicast streams, this is the multicast address assigned in Core Manager.

Bitrate (Mbps)

Specify the maximum average network video bitrate the Encoder can use to send AV streams to Decoders, from 50 to 800. The default is 750.

Lower bitrates consume less network bandwidth, but at the expense of compromised video quality during fast motion and transitions. For acceptable video quality:

• 4K60 stream – set the bitrate to at least 650 Mbps.
• 1080p streams – set to the bitrate so that each stream can use at least 250 Mbps.

Note: The Bitrate value is shared across all AV streams. For example, if you set the Bitrate to 600, the first AV stream can use a maximum of 600 Mbps. If a second stream becomes active, both streams can use 300 Mbps. If a third stream becomes active, each stream can use 200 Mbps.

Ref Frame Interval

This value determines how often video artifacts introduced by network errors are eliminated in the video stream. The value, between 90 and 255, is the number of video frames before a complete refresh occurs. The default is 90. A longer interval results in a lower video bitrate (thus consuming less network bandwidth), but at the expense of video artifacts persisting during the interval.

Encoder Mode

This property determines the maximum allowed AV stream resolution and what happens when the Encoder video streaming capabilities are exceeded.

• 4K60 max - One Hot Plug Event: (Default) This option allows a maximum stream resolution of 4K60. However, because an Encoder is limited to processing a single stream at resolutions above 1080p60, a request from a Decoder to process an additional AV stream on another input triggers a "hot plug event." Any Encoder input EDID with a resolution greater than 1080p60 is automatically re-negotiated down to 1080p60 maximum, thus allowing the Encoder to provide up to three streams. When this occurs, there is a momentary disruption of video processing across all AV streams. This negotiation and disruption mimic what occurs when unplugging and plugging back in an HDMI cable, hence the term. When all AV inputs become idle, the source EDIDs then reset to allow resolutions greater than 1080p60 again. Additionally, when wired to a dual output NV-32-H decoder, the encoder mode will switch to 1080p until the source is removed and the AV route is cleared.
• 1080p60 max - No Hot Plug Events: This option limits all streams to 1080p60 maximum. Because an Encoder can process three simultaneous streams up to 1080p60, there is no EDID re-negotiation when a Decoder requests subsequent streams. Wiring an encoder to a dual output NV-32-H will force this mode, limiting the input EDID on the encoder to 1080p or lower.

HDMI Output 1 Source

This section only appears when the HDMI Output Mode component property is set to "HDMI 1". Select which source to output through the Encoder's HDMI AV Output 1 pin. You can select a source using either the drop-down menu, numeric input, or trigger buttons. The Active HDMI LED indicates what sources are active and selectable.

• Graphic 1, 2, 3: Toggle a graphic to display that you assign in Q-SYS Core Manager. Numeric input values are 1, 2, and 3.
• HDMI 1, 2, 3: These inputs correspond to the sources connected to the HDMI AV Input pins 1, 2, 3. Numeric input values are 4, 5, and 6.
• Mediacast In n: These inputs correspond to the Mediacast sources (cameras) connected to the Mediacast Input pins. The number of selectable sources equals what is specified for the Mediacast > Input Count property. Numeric input values begin at 7.

HDMI Outputs

Select which sources to output through the Decoder's HDMI AV Output pins. The section for HDMI Output 2 Source only appears when the HDMI Output Mode component property is set to "HDMI 1 + HDMI 2". You can select a source using either the drop-down menu, numeric input, or trigger buttons. The Active AV LED indicates what sources are active and selectable.

• Graphic 1, 2, 3: Toggle a graphic to display that you assign in Q-SYS Core Manager. Numeric input values are 1, 2, and 3.
• HDMI 1, 2, 3: These inputs correspond to the sources connected to the HDMI AV Input pins 1, 2, 3. Numeric input values are 4, 5, and 6.
• AV 1 - n: These inputs correspond to the sources connected to the AV Input pins, where n is the value specified for the AV Input Count property. Numeric input values range from 7 to 9, depending on what is specified for the AV Input Count property.
• Mediacast In n: (HDMI Output 1 Source only) These inputs correspond to the Mediacast sources (cameras) connected to the Mediacast Input pins. The number of selectable sources equals what is specified for the Mediacast > Input Count property. Numeric input values range from 8 to 10, depending on what is specified for the AV Input Count and Mediacast Input Count properties.
• Follow H1: (HDMI Output 2 Source only) If the HDMI Output Mode property is set to "HDMI 1 + HDMI 2", this control appears for the HDMI Output 2 Source. When enabled, HDMI Output 2 uses whatever source is selected for HDMI Output 1. When enabled, the maximum resolution is 1080p60 for both outputs. Its numeric input value is one count after the last AV input value.

Pin Name	Value	String	Position	Pins Available
Output 1
Active
HDMI 1, 2, 3	0 1	false true	0 1	Output
Select
Follow HDMI Output 1	0 1	false true	0 1	Input / Output
Graphic 1, 2, 3	0 1	false true	0 1	Input / Output
HDMI 1, 2, 3	0 1	false true	0 1	Input / Output
Mediacast In n	0 1	false true	0 1	Input / Output
Mediacast Input
Focus
Auto Focus	0 1	false true	0 1	Input / Output
In	0 or momentary 1	0 or momentary 1	0.00 momentary 1.00	Input / Output
Out	0 or momentary 1	0 or momentary 1	0.00 momentary 1.00	Input / Output
Pan-Tilt-Zoom
Auto Privacy Delay	1.00 to 600	1.00s to 600s	0.00 1.00	Input / Output
Auto Privacy Mode	0 1	false true	0.00 1.00	Input / Output
Coordinates	N/A	Pan = -0.9936 to 0 to +0.9936 Tilt = -0.9936 to 2.9808 Zoom = 0.000000 to 1 Focus = 0.00000 to 1 The coordinates are entered in the above order, separated by a space.	N/A	Input / Output
Home	0 1	false true	0.00 1.00	Input / Output
Pan Left / Tilt Down	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Pan Left / Tilt Up	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Pan Right	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Pan Right / Tilt Down	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Pan Right / Tilt Up	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Privacy Mode	0 1	0 or false 1 or true	0.00 1.00	Input / Output
Tilt Down	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Tilt Up	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Zoom In	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Zoom Out	0 momentary 1	false momentary true	0.00 momentary 1.00	Input / Output
Source	0 n	0 n	0.000 to 1.00	Output
Source Type	(text)	Output
Select by Name	-	Graphic n HDMI n Follow H1	-	Input / Output
Select by Number	n (1 to n)	-	-	Input / Output
Output 21
Active
HDMI 1, 2, 3	0 1	false true	0 1	Output
Select
Follow HDMI Output 1	0 1	false true	0 1	Input / Output
Graphic 1, 2, 3	0 1	false true	0 1	Input / Output
HDMI 1, 2, 3	0 1	false true	0 1	Input / Output
	0 1	false true	0 1	Input / Output
Select by Name	-	Graphic n HDMI n Follow H1	-	Input / Output
Select by Number	n (1 to n)	-	-	Input / Output

¹ Output 2 only shows when HDMI Output Mode in Properties is set to HDMI 1 + HDMI 2.

¹Output 1 only shows when HDMI Output Mode in Properties is set to HDMI 1.

¹ Output 2 only shows when HDMI Output Mode in Properties is set to HDMI 1 + HDMI 2.