Generic AV Source

In an AV distribution topology using Q-SYS NV-32-H network video endpoints, the Generic AV Source component represents the beginning of the HDMI signal chain.

Input Pins

This component has no input pins.

Output Pins

AV Output

This pin represents the audio and video signals from the HDMI source. Connect this pin to one of the HDMI input pins of the HDMI I/O (NV-32-H) component . HDMI video and embedded audio signals are routed directly through the NV-32-H network video endpoint without the need for Q-SYS Core processing.

Note: You cannot wire a Generic AV Source component directly to a Generic HDMI Display component.

Note: For additional schematic examples, see the HDMI I/O (NV-32-H) topic.

Note: For more NV-32-H schematic examples showing different configurations for encoders, decoders, and displays, see HDMI I/O (NV-32-H) and Generic HDMI Display.

Tip: For additional properties not listed, refer to the Properties Panel help topic for more information.

Note: You must wire the source's HDMI AV Output pin to a NV-32-H  HDMI AV Input pin to expose the source controls.

Status

Component status is conveyed with the Status LED and Status box, which uses both color and text to indicate the current condition:

• OK: The device is functioning normally.
• Initializing: The device is in the process of a firmware or configuration update, or the design is starting.
• Compromised: The device is functioning, but a non-fatal problem exists. Refer to the Status box for details.
• Missing: The device cannot be discovered.
• Fault: The device is malfunctioning or is not properly configured. Refer to the Status box for details.
• Unknown: This status appears during a Core reboot (for example, during a firmware update), or when a design is being uploaded to the Core and before it has started running.
• Not Present: If applicable to the device, this status appears when the device is not connected to the network and its Is Required component property is set to 'No'. This status also appears if the device component's Dynamically Paired property is set to 'Yes', pairing has not been assigned in Core Manager, and the device component's Is Required property is set to 'Yes'. See Dynamic Pairing.

HDMI AV Output

HDMI +5v

LED indicates whether an external HDMI source is detected. (Some HDMI sources do not have a +5v signal and are not compatible with Q-SYS.)

Valid Format

LED indicates whether the HDMI input is receiving video that is compatible with Q-SYS. If this LED is not lit, it means that video is not detected on the input, is present but corrupt, or the video format is incompatible with the current operating mode - for example, a 4K60 signal is detected but 1080p60 is configured as the maximum format.

Tip: "Auto selection" scripts can use this LED as an indication that an input is active and usable.

Video Format

Displays the detected HDMI source resolution and frame rate. If the video format is incompatible (for example, interlaced input), invalid, or unrecognizable, the status indicates "Invalid".

Aspect Ratio

Displays the detected aspect ratio of the source video – for example, "16:9".

Active Audio Channels

Displays the number of active, valid, and usable embedded audio channels detected in the HDMI source video.

EDID

EDID files include properties for supported video resolutions, frame rates, number of audio channels, and audio formats. Select an EDID file to apply to the HDMI source, which is then sent to the NV-32-H encoder input. Q-SYS uses standard EDID files (with file extension .qedid) to tell HDMI sources what audio and video formats are compatible with the NV-32-H system. If you save a display's EDID file to the Q-SYS Core (using the Generic HDMI Display component's 'Save EDID to Core' control) or upload an EDID file in the Q-SYS Core Manager Video > Video Endpoints page, those EDID files also appear in this list and use the .bin file extension.

Note: Settings within EDIDs can be dynamically changed on the NV-32-H inputs depending on how you configure the NV-32-H – see the 'Max Supported Format' control and the 'Audio Channels' property.

Max Supported Format

Indicates the maximum video format supported in the current operating mode. There are two configuration scenarios in which the NV-32-H cannot accept video formats that exceed 1920x1080p60:

• If you set the NV-32-H I/O Decoder design property HDMI Output Mode to 'HDMI 1 + HDMI 2', both HDMI outputs are limited to 1920x1080p60 and smaller resolutions.
• If you set the NV-32-H I/O Encoder control Encoder Mode to '1080p60 max - No Hot Plug Events', all HDMI inputs wired to the encoder are limited to 1920x1080p60 and smaller resolutions.

Enable Output

Click to toggle Hot-Plug Detection (HPD) from the HDMI source. This is enabled by default. When Enable Output is toggled off, HDMI signals from the source are disabled and its status changes to "Not Present", which is the same behavior as physically disconnecting the source's HDMI cable.

Tip: Toggling Enable Output is useful, for example, if you have a PC with two HDMI outputs connected to an NV-32-H and you want to force the PC to use either single display mode (toggle off Enable Output on one of the outputs) or dual display mode (toggle on Enable Output on both outputs).

Hot-Plug Trigger

This resets the HDMI interface without having to physically disconnect and reconnect the source's HDMI cable. If you are experiencing HDMI signal issues, try pressing this button.

HDCP Mode

Select whether the NV-32-H HDMI input negotiates and authenticates HDCP with the source:

• Auto: (Default) Allows the source to negotiate HDCP 1.4 or 2.2 with the NV-32-H HDMI input. Note that when a source sends protected content, authentication can interrupt the video signal for up to 30 seconds.
• Off: The NV-32-H HDMI input does not negotiate HDCP with its source. The source cannot send protected content to the input.

CAUTION: Many sources do not provide notification of HDCP authentication failures and instead send black video, making it difficult to diagnose video issues. Use the 'Off' mode with care.

HDCP Status

Displays the HDMI input's HDCP negotiated state.

HDCP Encryption

LED indicates whether HDCP encryption is active on the source's HDMI output.

HDMI Audio

This section shows information for all HDMI source audio channels, as configured in the 'Audio Channels' property.

Valid

LED glows green when the embedded audio for a channel is currently being sent from the Generic AV Source component.

Peak Input Level (dBFS)

Meter displaying the detected peak level of the HDMI audio, from -120 dB to 20 dB.

Invert

Click to invert the polarity of the audio signal.

Mute

Click to mute the audio signal.

Gain

Click to adjust the gain of the audio signal, from -100 dB to 20 dB (default is 0).